Download File

Transcript
Testing the UMTS Iu Interface
▲
▲
Application Note
Table of Contents
1.
Testing the UMTS Iu Interface
INTRODUCTION – THE Iu INTERFACE AND PROTOCOLS ..................................................................................................................................................3
1. Introduction – The Iu Interface and
Protocols
Application Note
All traffic over the Iu interface uses the Asynchronous Transfer Mode (ATM) as
the physical transport technology, regardless of the data source. As a result, all
data will be segmented into 53-byte ATM-cells and transported
1.1. TRANSPORT PROTOCOLS FOR THE CONTROL PLANE ........................................................................................................................................3
1.2. TRANSPORT PROTOCOLS FOR THE USER PLANE ..............................................................................................................................................3
2.
This document describes test applications for the Iu interface as it was defined
by 3GPP at the end of 1999 (UMTS Rel. ‘99). Change requests have been
1.3. CONTROL PROTOCOLS FOR CALL CONTROL, SESSION AND MOBILITY MANAGEMENT..........................................................................................4
introduced and new features have been proposed every three months since
1.4. PROTOCOLS FOR USER TRAFFIC ....................................................................................................................................................................4
that definition was adopted, so it is possible that there will be revisions in more
MEASUREMENT CHALLENGES AND SOLUTIONS ............................................................................................................................................................4
Monitoring ............................................................................................................................................................................4
2.1.2.
Simulation ............................................................................................................................................................................5
2.1.3.
Emulation ..............................................................................................................................................................................5
2.1.4.
Conformance Testing. ............................................................................................................................................................5
2.2. CONFIGURING THE TEST EQUIPMENT ..............................................................................................................................................................6
Transport protocols for the control plane consist of the SSCS signaling
The Iu interface is defined in the 3GPP document series TS25.410-419. Iu is
subdivided into two different interfaces: Iu-CS for the circuit switched domain
and Iu-PS for the packet switched domain. Figures 1 and 2 show the protocol
stacks for each of the Iu interfaces.
datagrams. Loss of signaling messages can be detected and
retransmitted. SCCP is used to setup specific connections for the
connection-oriented communications. Iu normally uses the connection-
The protocols can be grouped according to their usage into:
oriented mode.
Hardware Connection Issues ....................................................................................................................................................6
• transport protocols for control plane
2.2.2.
Setting the Operating Parameters ............................................................................................................................................7
• transport protocols for user plane
MTP3b handles the routing and traffic management function for upper
2.2.3.
Defining Protocol Stacks ........................................................................................................................................................7
• control protocols for call, session, mobility management
layer protocols. It delivers messages to the destination point and
2.2.4.
Defining Emulation Parameters ................................................................................................................................................8
• protocols for user traffic
2.3.2.
manages the load sharing mechanism for the operation. MTP3b is
responsible for routing messages within a network with one operator;
SCCP routes messages beyond the board of an operator. While the
Simulation of AAL2 layer 3 ......................................................................................................................................................9
Radio
Network
Control
Plane
Emulation of AAL2 layer 3 ....................................................................................................................................................11
Transport
Network
Control
Plane
User
Plane
Data
Services
RANAP
AAL2L3
RLP
SCCP
STC
CC/MM/GPRS
MM/GPRS SM
2.4. TESTING RANAP AND DMTAP ........................................................................................................................................................................12
connections between the RNC and Core Network nodes are shown here
User
Plane
Voice
Services
as point-to-point, these connections could also be incumbent networks
consisting of several interim nodes.
TAF
AMR Codec
Iu UP
2.5. TESTING OF THE GTP-U PROTOCOL ..............................................................................................................................................................13
MTP3-b
SSCF-UNI
CONCLUSION ..............................................................................................................................................................................................................14
The most logical approach for Iu-PS would be to use the IP protocol stack
SSCOP
to transport the control signaling information. For this reason, the Internet
AAL2
AAL5
APPENDIX I ................................................................................................................................................................................................................15
Engineering Task Force (IETF) has proposed to replace SSCS and MTP3b
ATM
4.1. RECOMMENDED DOCUMENTS AND STANDARDS ............................................................................................................................................15
with M3UA and SCTP protocols on top of UDP/IP. Since this protocol stack
▲
4.2. GLOSSARY ..................................................................................................................................................................................................16
5.
ensure the signaling links between network nodes with numbered
2.2.1.
2.3.1.
4.
protocols (SSCOP and SSCF) as they are used in broadband networks to
different control signaling protocols, enabling both connectionless and
2.3. TESTING AAL2 LAYER 3 ..................................................................................................................................................................................9
3.
1.1. Transport Protocols for the Control Plane
recent releases of the standard.
2.1. SELECTING THE APPROACH – MONITORING , SIMULATION, EMULATION, CONFORMANCE ....................................................................................4
2.1.1.
asynchronously.
is still under development, there are no application tests for it in this
Figure 1: Iu-CS protocol stack
release of the note.
APPENDIX II – UMTS – Entering the Third Generation of Mobile Networks ................................................................................................................20
Radio Network
Control Plane
Transport Network
Control Plane
User Plane
CC/MM/GPRS MM/GPRS SM
IP
RANAP
Iu UP
1.2. Transport Protocols for the User Plane
SCCP
MTP3-b
M3UA
SSCF-NNI
SCTP
GTP-U
UDP
SSCOP
IP/UDP
AAL5
IP
AAL5
ATM
All signaling traffic for the control plane at the Iu interface is based on
AAL type 5. Signaling messages are packet data with variable lengths.
However, transport protocols for the user plane use both AAL5 and AAL2
(AAL5 for packet data, AAL2 for circuit-switched transmission).
▲
2 www.tektronix.com/commtest
Figure 2: Iu-PS protocol stacks
www.tektronix.com/commtest
3