Download File
Transcript
Testing the UMTS Iu Interface ▲ ▲ Application Note Table of Contents 1. Testing the UMTS Iu Interface INTRODUCTION – THE Iu INTERFACE AND PROTOCOLS ..................................................................................................................................................3 1. Introduction – The Iu Interface and Protocols Application Note All traffic over the Iu interface uses the Asynchronous Transfer Mode (ATM) as the physical transport technology, regardless of the data source. As a result, all data will be segmented into 53-byte ATM-cells and transported 1.1. TRANSPORT PROTOCOLS FOR THE CONTROL PLANE ........................................................................................................................................3 1.2. TRANSPORT PROTOCOLS FOR THE USER PLANE ..............................................................................................................................................3 2. This document describes test applications for the Iu interface as it was defined by 3GPP at the end of 1999 (UMTS Rel. ‘99). Change requests have been 1.3. CONTROL PROTOCOLS FOR CALL CONTROL, SESSION AND MOBILITY MANAGEMENT..........................................................................................4 introduced and new features have been proposed every three months since 1.4. PROTOCOLS FOR USER TRAFFIC ....................................................................................................................................................................4 that definition was adopted, so it is possible that there will be revisions in more MEASUREMENT CHALLENGES AND SOLUTIONS ............................................................................................................................................................4 Monitoring ............................................................................................................................................................................4 2.1.2. Simulation ............................................................................................................................................................................5 2.1.3. Emulation ..............................................................................................................................................................................5 2.1.4. Conformance Testing. ............................................................................................................................................................5 2.2. CONFIGURING THE TEST EQUIPMENT ..............................................................................................................................................................6 Transport protocols for the control plane consist of the SSCS signaling The Iu interface is defined in the 3GPP document series TS25.410-419. Iu is subdivided into two different interfaces: Iu-CS for the circuit switched domain and Iu-PS for the packet switched domain. Figures 1 and 2 show the protocol stacks for each of the Iu interfaces. datagrams. Loss of signaling messages can be detected and retransmitted. SCCP is used to setup specific connections for the connection-oriented communications. Iu normally uses the connection- The protocols can be grouped according to their usage into: oriented mode. Hardware Connection Issues ....................................................................................................................................................6 • transport protocols for control plane 2.2.2. Setting the Operating Parameters ............................................................................................................................................7 • transport protocols for user plane MTP3b handles the routing and traffic management function for upper 2.2.3. Defining Protocol Stacks ........................................................................................................................................................7 • control protocols for call, session, mobility management layer protocols. It delivers messages to the destination point and 2.2.4. Defining Emulation Parameters ................................................................................................................................................8 • protocols for user traffic 2.3.2. manages the load sharing mechanism for the operation. MTP3b is responsible for routing messages within a network with one operator; SCCP routes messages beyond the board of an operator. While the Simulation of AAL2 layer 3 ......................................................................................................................................................9 Radio Network Control Plane Emulation of AAL2 layer 3 ....................................................................................................................................................11 Transport Network Control Plane User Plane Data Services RANAP AAL2L3 RLP SCCP STC CC/MM/GPRS MM/GPRS SM 2.4. TESTING RANAP AND DMTAP ........................................................................................................................................................................12 connections between the RNC and Core Network nodes are shown here User Plane Voice Services as point-to-point, these connections could also be incumbent networks consisting of several interim nodes. TAF AMR Codec Iu UP 2.5. TESTING OF THE GTP-U PROTOCOL ..............................................................................................................................................................13 MTP3-b SSCF-UNI CONCLUSION ..............................................................................................................................................................................................................14 The most logical approach for Iu-PS would be to use the IP protocol stack SSCOP to transport the control signaling information. For this reason, the Internet AAL2 AAL5 APPENDIX I ................................................................................................................................................................................................................15 Engineering Task Force (IETF) has proposed to replace SSCS and MTP3b ATM 4.1. RECOMMENDED DOCUMENTS AND STANDARDS ............................................................................................................................................15 with M3UA and SCTP protocols on top of UDP/IP. Since this protocol stack ▲ 4.2. GLOSSARY ..................................................................................................................................................................................................16 5. ensure the signaling links between network nodes with numbered 2.2.1. 2.3.1. 4. protocols (SSCOP and SSCF) as they are used in broadband networks to different control signaling protocols, enabling both connectionless and 2.3. TESTING AAL2 LAYER 3 ..................................................................................................................................................................................9 3. 1.1. Transport Protocols for the Control Plane recent releases of the standard. 2.1. SELECTING THE APPROACH – MONITORING , SIMULATION, EMULATION, CONFORMANCE ....................................................................................4 2.1.1. asynchronously. is still under development, there are no application tests for it in this Figure 1: Iu-CS protocol stack release of the note. APPENDIX II – UMTS – Entering the Third Generation of Mobile Networks ................................................................................................................20 Radio Network Control Plane Transport Network Control Plane User Plane CC/MM/GPRS MM/GPRS SM IP RANAP Iu UP 1.2. Transport Protocols for the User Plane SCCP MTP3-b M3UA SSCF-NNI SCTP GTP-U UDP SSCOP IP/UDP AAL5 IP AAL5 ATM All signaling traffic for the control plane at the Iu interface is based on AAL type 5. Signaling messages are packet data with variable lengths. However, transport protocols for the user plane use both AAL5 and AAL2 (AAL5 for packet data, AAL2 for circuit-switched transmission). ▲ 2 www.tektronix.com/commtest Figure 2: Iu-PS protocol stacks www.tektronix.com/commtest 3