Download SETTING INSTRUCTIONS

Transcript
Setting record for thermostat set for
six events each day
Setting record for thermostat set for
two events each day
Event Numbers
Format
1
2
CLG
HTG
Event Number
3
CLG
HTG
CLG
4
HTG
5
CLG
HTG
CLG
6
HTG
CLG
HTG
Format
1
Pre-set programmes, Monday to Friday
25.0°C
20.0°C
27.2°C
6:30
15.0°C
8:30
25.0°C
20.0°C
27.2°C
11:30
2
CLG
15.0°C
25.0°C
13:30
20.0°C
27.2°C
16:30
CLG
Time
15.0°C
22:30
HTG
HTG
TIme
Pre-set programmes, Monday to Friday
Actual User Settings, Monday to Friday
25.0°C
1 (Monday)
21.1°C
Off
8:30
15.0°C
17:30
Actual User Settings, Monday to Friday
2 (Tuesday)
1 (Monday)
3 (Wednesday)
4 (Thursday)
2 (Tuesday)
5 (Friday)
3 (Wednesday)
Pre-set Programmes, Saturday & Sunday
27.2°C
20.0°C
27.2°C
7:30
20.0°C
9:30
25.0°C
20.0°C
25.0°C
11:30
20.0°C
25.0°C
13:30
21.1°C
27.2°C
16:30
15.0°C
22:30
4 (Thursday)
Actual User Settings, Saturday & Sunday
5 (Friday)
6 (Saturday)
Pre-set Programmes, Saturday & Sunday
7 (Sunday)
Off
Off
8:30
If the unit is to operate in 5/2 day mode, then only days 1 and 6 need be completed.
Off
Off
17:30
Actual User Settings, Saturday & Sunday
6 (Saturday)
NOTES ON SETTING EVENT TIMES
7 (Sunday)
(Assumes unit is in 6 events/day mode)
If, during the event checking and setting procedure, no buttons are
pressed for more than two minutes then the HP75 will return to RUN
mode automatically. If this appears to have occurred, it is advisable to
re-check the program to ensure that it is as required.
When setting event times and temperatures it is not possible to set
event times out of chronological order.
Event 1 may be set at any time from 0:00AM to 11:59PM (but would
normally be in the morning).
Event 2 may be set at any time between event 1 and 23 hours, 59
minutes after event 1.
If the event time being set is moved past midnight into the following day
then the number of the following day will blink.
15.0°C
00:30
12:30am
Event 6 on day 6 set after
midnight.
EVENT 6
5°C
DEAD
BAND
FACTORY
PRE-SET
PROGRAMME
HEATING
12:00
15:00
EVENTS
2, 3 & 4
18:00
21:00
MIDNIGHT
In the diagram opposite, event 2 has been moved to 3:30PM. Note that
events 3 & 4 have also been moved to that time and that the following
control temperature will be that of event 4.
EVENT 6
9:00
EVENT 5
6:00
EVENT 1
3:00
COOLING
EXAMPLE
USER SET
PROGRAMME
HEATING
MIDNIGHT
2
The factory pre-set programme may be reinstated by pressing the
recessed RESET button. This will however reinstate all the factory preset conditions so that the clock type and temperature scale may also
have to be re-set.
COOLING
MIDNIGHT
32°C
31°C
30°C
29°C
28°C
27°C
26°C
25°C
24°C
23°C
22°C
21°C
20°C
19°C
18°C
17°C
16°C
15°C
14°C
13°C
EVENT 5
EVENT 1
32°C
31°C
30°C
29°C
28°C
27°C
26°C
25°C
24°C
23°C
22°C
21°C
20°C
19°C
18°C
17°C
16°C
15°C
14°C
13°C
EVENT 4
When using the - button to adjust events 2 to 6 and the previous event
time is reached the - button ceases to respond.
EVENT 3
Event 4 may be set at any time between event 3 and 23 hours, 59
minutes after event 1,.... and so on.
EVENT 2
Event 3 may be set at any time between event 2 and 23 hours, 59
minutes after event 1.
When using the + button to adjust events 1 to 5 and the event time
being adjusted becomes the same as the following event time, then
both are changed simultaneously. This applies to all subsequent event
times reached and is demonstrated in the diagram on the lower left.
3:00
It is possible to move events past midnight into the following day when
the day number will blink in the display, see the display diagram in the
notes on setting event times.
3°C
DEAD
BAND
Manual overide
used =atUSED
9am
MANUAL OVERRIDE
AT 9 AM TO RAISE
to raise temperature
by 2°C.
TEMPERATURE BY 2°C.
PROGRAMMED
3°C
DEAD
Programmed
3°C dead band
BAND MAINTAINED.
maintained.
6:00
9:00
12:00
15:00
18:00
21:00
MIDNIGHT