Download APC Back-UPS

Transcript
Status Indicators
Status
LED Indicator
Audible Indicator On
Audible Indicator Terminates
Power On
The Back-UPS is supplying utility power to connected equipment.
The green LED illuminates.
On Battery
Back-UPS supplying battery power to battery backup outlets.
The green LED illuminates. The LED Back-UPS beeps 4
Beeping stops when utility power is restored or
is not illuminated during the beeps.
times every 30 seconds. the Back-UPS is turned off.
None
N/A
Low Battery warning
The Back-UPS emits
The green LED illuminates with rapid
The Back-UPS is supplying battery power to the battery backup outlets
rapid beeping, every
green flashes.
and the battery is near a total discharge state.
1/2 second.
Replace Battery
Constant tone
• Replace Battery LED flashes.
• Replace Battery and Power On
LEDs flash alternately.
• The battery is disconnected.
• The battery needs to be charged, or replaced.
Overload Shutdown
While on battery power an overload condition has occurred in one or
None
more of the battery backup outlets while the Back-UPS is operating on
battery power.
Sleep Mode
While on battery power the battery is completely discharged. The
Back-UPS will “awaken” once utility power is restored.
Building Wiring Fault
Building Wiring Fault LED
The building wiring presents a shock hazard that must be corrected by a illuminates red
qualified electrical.
Solution
The Back-UPS will not turn on
The Back-UPS has not been turned
on.
Press the POWER ON button.
The Back-UPS is not connected to
utility power, there is no utility power
available at the wall outlet, or the
utility power is experiencing a
brownout or over voltage condition.
Make sure the power cord is securely connected to
the wall outlet, and that there is utility power
available at the wall outlet.Where applicable,
check that the wall outlet is switched on.
The battery is not connected.
Connect the battery. Refer to “Connect the
Battery” on page 1 of this manual.
In the event that the Back-UPS receives no utility
power and the battery is connected, a cold-start can
be initiated. Press and hold the Power On button
until the Back-UPS emits two beeps.
None
The beeping stops when:
• Utility power is restored
• If utility power is not restored within 32 seconds
• The Back-UPS is turned off
The Back-UPS is unplugged from the wall outlet
or is plugged into an improperly wired outlet.
2. Press and hold the ON/OFF button for 10 seconds. The OnLine LED will
illuminate alternately green-amber-red, to indicate that the Back-UPS is in
Program mode.
3. The Power On/Replace Battery LED will flash either green, amber, or red to
indicate the current sensitivity level. Refer to the table for an explanation of the
transfer voltage sensitivity levels.
4. To select LOW sensitivity, press and hold the ON/OFF button until the LED flashes
green.
5. To select MEDIUM sensitivity, press and hold the ON/OFF button until the LED
flashes red.
6. To select HIGH sensitivity, press and hold the ON/OFF button until the LED flashes
amber.
Refer to the “Connect the Battery” on page 1.
Remove all nonessential equipment connected to
the outlets. One at a time reconnect equipment to
the Back-UPS.
Connect the Back-UPS to utility power and allow
the battery to recharge for eight hours.
PowerChute software has performed a This is normal Back-UPS operation.
shutdown due to a power failure.
Connected equipment does not accept The output waveform is intended for computers
the step-approximated sine waveform and peripheral devices. It is not intended for use
from the Back-UPS.
with motor driven equipment.
The Back-UPS may require service.
Back-UPS is turned off.
1. Connect the Back-UPS to a wall outlet. The Back-UPS will be in Standby mode, no
indicators will be illuminated.
7. To exit Program mode wait five seconds and all LED indicators will extinguish.
Program mode is no longer active.
Connected equipment loses power
The Back-UPS battery is completely
discharged.
Constant tone
The Back-UPS detects and reacts to line voltage distortions by transferring to battery
backup power to protect connected equipment. In situations where either the Back-UPS
or the connected equipment is too sensitive for the input voltage level it is necessary to
adjust the transfer voltage.
The Back-UPS is on, the Replace Battery LED flashes and the unit emits a
constant tone
A Back-UPS overload condition has
occurred.
Back-UPS is turned off.
Voltage Sensitivity Adjustment (optional)
Problem and Possible Cause
The battery is disconnected.
Constant tone
The Back-UPS beeps
once every four
seconds.
None
Troubleshooting
Beeping stops when utility power is restored or
the Back-UPS is turned off.
LED Sensitivity Input Voltage Range
Flashes Setting (Utility Operation)
88 Vac to 142 Vac
LOW
Red
MEDIUM 92 Vac to 139 Vac
Factory default setting. Use this setting
under normal conditions.
Amber
HIGH
Use this setting when connected equipment
is sensitive to voltage and waveform
fluctuations.
96 Vac to 136 Vac
Contact APC Technical Support for more in depth
troubleshooting.
The Power On LED is illuminated and the Back-UPS beeps 4 times every 30
seconds
The Back-UPS is operating on battery The Back-UPS is operating normally on battery
power.
power. At this point the user should save all open
files, and shutdown the computer. When utility
power is restored the battery will recharge.
Recommended Use
Green
Use this setting with equipment that is less
sensitive to fluctuations in voltage or
waveform distortions.
Service
If the unit requires service, do not return it to the dealer. Follow these steps:
1. Review the Troubleshooting section of the manual to eliminate common problems.
2. If the problem persists, contact APC Customer Support.
The Power On LED flashes once every second while the Back-UPS beeps once
every second
a. Note the model number and serial number and the date of purchase. The model
and serial numbers are located on the rear panel of the unit and are available
through the LCD display on select models.
The Back-UPS battery has
approximately two minutes of
remaining runtime.
b. Call APC Customer Support and a technician will attempt to solve the problem
over the phone. If this is not possible, the technician will issue a Returned
Material Authorization Number (RMA#).
The Back-UPS battery is near a total discharge
state. At this point the user should save all open
files, and shutdown the computer. When utility
power is restored the battery will recharge.
The Building Wiring Fault LED illuminates
The building wiring presents a shock
hazard that must be corrected by a
qualified electrical.
Do not operate the Back-UPS. Call a qualified
electrician to correct the building wiring fault.
The Back-UPS has an inadequate battery runtime
The battery is not fully charged.
The battery is near the end of useful
life and should be replaced.
Leave the Back-UPS connected to utility power for
16 hours while the battery charges to full capacity.
As a battery ages, the runtime capability decreases.
Contact APC at the Web site www.apc.com, to
order replacement batteries.
The connection from the Back-UPS to the internet is lost during a power
outage
The modem has lost power.
Connect the modem cable into one of the Battery
Backup + Surge Protection outlets.
c. If the unit is under warranty, the repairs are free.
d. Service procedures and returns may vary internationally. Refer to the APC Web
site for country specific instructions.
3. Pack the unit properly to avoid damage in transit. Never use foam beads for
packaging. Damage sustained in transit is not covered under warranty. Always
DISCONNECT THE UPS BATTERY before shipping in compliance with U.S.
Department of Transportation (DOT) and IATA regulations. The battery may
remain in the unit.
4. Write the RMA# provided by Customer Support on the outside of the package.
5. Return the unit by insured, pre-paid carrier to the address provided by
Customer Support.
Contact
APC Web site, www.apc.com
© 2011 APC by Schneider Electric. APC, the APC logo, Back-UPS and PowerChute are owned by Schneider Electric Industries S.A.S., American Power Conversion Corporation,
or their affiliated companies. All other trademarks are property of their respective owners.
990-3951B
7/2011