Download Lecture Notes - Unit 8
Transcript
ELECTRICAL AND COMPUTER ENGINEERING DEPARTMENT, OAKLAND UNIVERSITY ECE-470/570: Microprocessor-Based System Design Fall 2014 PORT S General Purpose I/O (GPIO) Port. Data Register (PTS): $0248. Data Direction Register (DDRT): $024A. ‘1’ means output, ‘0’ means input Dragon12-Light Board: External I/O pins. Also, PS0 is RXD0 (SCI0 Receive), PS1 is TXD0 (SCI0 Transmit), PS2 is RXD1 (SCI1 Receive), PS3 is TXD1 (SCI1 Transmit), PS4 is MISO0 (SPI0 input), PS5 is MOSI0 (SPI0 output), PS6 is SCK0 (SPI0 clock output), and PS7 is /SS0 (SPI0 output enable). Note that the DAC (LTC1661) uses SPI to communicate and utilizes the pins PS5 (MOSI0) and PS6 (SCK0). PORT M General Purpose I/O (GPIO) Port. Data Register (PTM): $0250. Data Direction Register (DDRM): $0252. ‘1’ means output, ‘0’ means input Module Routing Register (MODRR): $0257. This register configures the rerouting of CAN and SPI ports on defined port pins. Dragon12-Light Board: External I/O pins. Also, PM0 is CAN0 Receive, PM1 is CAN0 Transmit. The CAN chip is the MCP2551. Also, PM2 is the common anode (in negative logic) of the RGB LED, PM6 is the Chip Select (CS) input of the DAC (LTC1661). PORT H General Purpose I/O (GPIO) Port. Data Register (PTH): $0260. Data Direction Register (DDRH): $0262. ‘1’ means output, ‘0’ means input Dragon12-Light Board: External I/O pins. Also, they are connected to the DIP switch and Push Buttons (4 LSBs). PORT J General Purpose I/O (GPIO) Port. Data Register (PTJ): $0268. Data Direction Register (DDRH): $026A. ‘1’ means output, ‘0’ means input Dragon12-Light Board: External I/O pins. Also, PJ6 is the SDA pin (I2C), PJ7 is the SCL pin (I2C). PORT P General Purpose I/O (GPIO) Port. Data Register (PTP): $0258. Data Direction Register (DDRP): $025A. ‘1’ means output, ‘0’ means input If PWM is enabled, all PORT P pins can become PWM channels. Dragon12-Light Board: External I/O pins. Also, PP0-PP3 are the cathodes of the 7-segment displays. PP0-PP1 are connected to the DC Motor Driver (TB6612F NG). Also PP4-PP6 are the anodes (in negative logic) of the RGB LED. With a jumper, PP5 connects to the buzzer. PORTS AD0 AND AD1 These ports are analog input interfaces to the ADC subsystem. Each ADC has 8 channels. ATD0 Data Register (PORTAD0): $008F. ATD0 Digital Input Enable Register (ATD0DIEN): $008D. We can configure each input channel as analog input (0) or as digital input (1). ATD1 Data Register (PORTAD1): $012F. ATD1 Digital Input Enable Register (ATD1DIEN): $012D. We can configure each input channel as analog input (0) or as digital input (1). Dragon12-Light Board: External input pins. Also, some pins are connected to the light sensor, temperature sensor, Trimmer Pot (see Board User Manual). PAD0-PAD7: ATD0, PAD8-PAD15: ATD1? ELECTRICAL CHARACTERISTICS CONSIDERATIONS FOR I/O INTERFACING In addition to the microcontroller, most embedded systems use peripherals (or I/O devices). These peripherals usually feature an integrated circuit (IC). Because these ICs might use different technologies, we must make sure that they are electrically compatible: Voltage-level compatibility: The high output level of the IC must match that of another IC (which can be the microcontroller itself). Same for the low output level. Current drive capability: The output of an IC might not have enough current to drive its load. Moreover, the total current required to drive I/O devices might exceed the maximum current rating for the microcontroller. This problem is usually solved by adding buffer chips (powered externally, e.g.: 74ABT244) that can supply enough current between the microcontroller and the peripheral ICs. Another issue is Timing compatibility. An I/O pin configured as an input usually has a register that reads from a peripheral pin. An I/O pin configured as an output usually has a register whose value is read by the peripheral pin (possibly on a register). We must make sure not to violate the setup and hold time requirements on the flip flops. 2 Instructor: Daniel Llamocca