Download Emerson V150 User Guide

Transcript
Product Flier
PF51.3:Vee-Ball
May 2009
High-Capacity Rotary Valves
Maximum Inlet Pressure for CW2M Valve Bodies
Table 12. Maximum Inlet Pressure for CW2M Valve Bodies
TEMPERATURE, C
MAXIMUM INLET PRESSURE,
BAR
150
300
600
46 to 38
93
149
204
232
20.0
17.9
15.9
13.8
12.8
51.7
51.7
50.3
48.6
47.2
NOTE
CW2M is not listed in ASME
B16.34. The designations 150, 300,
and 600 indicate relative
pressure-retaining capabilities and
are not ASME
pressure-temperature rating
classes.
103
103
100
97.2
94.5
Shutoff Pressure Drop Limits for Trim Parts
the EN or ASME pressure-temperature rating of
the valve or mating flanges, as exceeding the
pressure-temperature rating may cause personal
injury or equipment damage.
WARNING
Pressure drops in the following table consider
only the trim parts (ball, shafts, bearings, and
seals).
In the following tables, the lower temperature limit is
10C for EN valves, 29C for ASME steel valves,
and 46C for ASME stainless steel valves.
The pressure drops shown might be higher than
the EN or ASME pressuretemperature rating of
the valve body or mating flanges. Do not exceed
Also refer to the actuator sizing pages to select an
actuator size.
Table 13. Pressure Drop in Bar (For HD Metal Seal, Pressure Drops are for Forward Flow Only. For Reverse HD Seal Flow, Limit
Pressure Drop to 6.9 Bar)
VALVE SIZE
BEARING
MATERIAL
1
1-1/2
2
3
4
6
8
10
12
-46 to 38
DN
25
51.0
DN
40
51.0
DN
50
51.0
DN
80
51.0
DN
100
51.0
DN
150
51.0
DN
200
51.0
DN
250
40.2
DN
300
37.6
14
16
20
---
---
---
93
37.9
37.9
37.9
37.9
37.9
37.9
37.9
37.9
37.6
31.0
23.8
31.0
31.0
23.8
149
24.1
24.1
24.1
24.1
24.1
24.1
24.1
24.1
31.0
24.1
24.1
23.8
204
10.3
10.3
10.3
10.3
10.3
10.3
10.3
24.1
10.3
10.3
10.3
10.3
232
3.45
3.45
3.45
3.45
3.45
3.45
10.3
3.45
3.45
3.45
3.45
3.45
HD Metal
-46 to 288
51.0
51.0
51.0
51.0
51.0
3.45
51.0
51.0
40.9
38.1
40.3
26.5
Flat Metal
-29 to 260
---
---
---
20.7
40.3
20.7
20.7
20.7
10.3
10.3
---
---
Flow Ring
---
99.3
99.3
99.3
99.3
---
72.4
75.2
73.8
40.5
37.7
40.5
35.0
44.7
HD Metal
-46 to 288
51.0
50.0
25.7
Flat Metal
-29 to 260
---
---
---
17.5
11.0
10.9
11.2
6.14
5.72
6.14
7.52
6.83
17.0
10.1
10.7
10.6
5.86
5.52
---
---
Flow Ring
---
74.5
49.6
---
26.8
18.8
10.9
11.2
11.1
6.07
5.65
6.07
7.31
6.69
HD Metal
-46 to 288
51.0
Flat Metal
-29 to 260
---
51.0
51.0
35.0
22.1
21.8
22.5
12.3
11.4
12.3
13.2
13.7
---
---
20.7
20.1
20.7
20.7
10.3
10.3
---
---
Flow Ring
---
---
99.3
99.3
53.5
37.6
21.8
22.5
22.2
12.1
11.3
12.1
14.6
13.4
HD Metal
Flat Metal
-46 to 288
51.0
51.0
51.0
---
---
---
---
---
---
20.5
13.2
14.0
-29 to 260
---
---
---
---
---
---
---
---
---
---
---
---
Flow Ring
---
99.3
99.3
88.9
---
---
---
---
---
---
20.2
20.1
22.3
HD Metal
-46 to 288
---
---
---
51.0
36.7
36.3
37.4
20.5
19.1
---
---
---
Flat Metal
-29 to 260
---
---
---
20.7
20.7
20.7
20.7
10.3
10.3
---
---
---
Flow Ring
---
---
---
---
62.7
36.3
37.4
37.0
20.2
18.8
---
---
---
BALL SEAL
TCM Plus
PEEK/PTFE
R30006
R30006
Silver Plated
S44004
S31600L
Nitride
TEMPERATURE,
C
15