Download USER MANUAL

Transcript
Pin Assignments - Common Connectors
Note: Not all connectors may be available on your specific product. This depends on the amount of additional hardware installed from factory,
or customized solutions. These pin assignments are for the common connectors used. Connectors are seen from users Point Of View (POV).
Pin Assignments - 24P DVI-I
1 2 3 4 5 6 7 8 C1 C2
9 10 11 12 13 14 15 16
C5
17 18 19 20 21 22 23 24 C3 C4
Pin 01
Pin 02
Pin 03
Pin 04
Pin 05
Pin 06
Pin 07
Pin 08
Pin 09
Pin 10
Pin 11
Pin 12
Pin 13
Pin 14
Pin 15
Pin 16
Pin 17
Pin 18
Pin 19
Pin 20
Pin 21
Pin 22
Pin 23
Pin 24
Pin C1
Pin C2
Pin C3
Pin C4
Pin C5
T.M.D.S. Data2 - (Digital - RED link 1)
T.M.D.S. Data2 + (Digital + RED link 1)
T.M.D.S. Data2/4 Shield
T.M.D.S. Data4 - (Digital - GREEN link 2)
T.M.D.S. Data4 + (Digital + GREEN link 2)
DDC Clock
DDC Data
Analog Vertical Sync (DVI-I only)
T.M.D.S. Data1 - (Digital - GREEN link 1)
T.M.D.S. Data1 + (Digital + GREEN link 1)
T.M.D.S. Data1/3 Shield
T.M.D.S. Data3 - (Digital - BLUE link 2)
T.M.D.S. Data3 + (Digital + BLUE link 2)
+5V Power (for standby mode)
Ground (for +5V and analog sync)
Hot Plug Detect
T.M.D.S. Data0 - (Digital - BLUE link 1) and digital sync.
T.M.D.S. Data0 + (Digital + BLUE link 1) and digital sync.
T.M.D.S. Data0/5 Shield
T.M.D.S. Data5 - (Digital - RED link 2)
T.M.D.S. Data5 + (Digital - RED link 2)
T.M.D.S. Clock Shield
T.M.D.S. Clock + (Digital clock + (Links 1 and 2)
T.M.D.S. Clock - (Digital clock - (Links 1 and 2)
Analog RED
Analog GREEN
Analog BLUE
Analog Horizontal Sync.
Analog Ground (return for RGB signals)
DDC = Display Data Channel /// T.M.D.S = Transition Minimized Differential Signal /// PIN C1,C2,C3,C4 = Only present on DVI-I connectors.
NOTE: Connector shows a DUAL LINK design, but some units may not support it. Only products with 1920x1200 or more in resolution
require / support DUAL LINK.
Pin Assignments - 15P HD RGB VGA
5 4 3 2 1
10 9 8 7 6
Pin Assignments - USB TYPE B
Pin 2: Negative Data
Pin 3: Positive Data
Pin 01
Pin 02
Pin 03
Pin 04
Pin 05
Pin 06
Pin 07
Pin 08
Pin 09
Pin 10
Pin 11
Pin 12
Pin 13
Pin 14
Pin 15
15 14 13 12 11
Red, analog
Green, analog
Blue, analog
Reserved for monitor ID bit 2 (grounded)
Digital ground
Analog ground red
Analog ground green
Analog ground blue
+5V power supply for DDC (optional)
Digital ground
Reserved for monitor ID bit 0 (grounded)
DDC serial data
Horizontal sync or composite sync, input
Vertical sync, input
DDC serial clock
Appendix
IND100241-9
80
Pin 1: VCC +5V
Pin 4: Ground