Download MEGA STAR 50

Transcript
MEGA STAR 50
1. Assembling the model
1.1 Preparation, explanatory notes
The numbers in brackets () refer to the part numbers in the Parts List at the end of the instructions.
The fuselages are hand-moulded and are likely to exhibit minor variations and irregularities on
the inside, especially along the central joint seam. Little work is required prior to installing the
main mechanics. The side windows are carefully arranged to provide good access to important
sections of the mechanics. Before finally installing any part check carefully that it fits, trim where
necessary and carry out a “dry run” (without glue). Take your time and work steadily and
patiently. All screwed joints except those involving plastic and those with self-locking nuts must
be secured with thread-lock fluid; this is a basic rule, and is not mentioned at every stage in the
instructions. Where extra items and accessory components are used they should be prepared
and installed as described in the instructions supplied with them.
1.1.1 Fuselage
Glued joints: to obtain sufficiently strong joints, all GRP parts must be roughened thoroughly on
the inside where they are to be glued. Use coarse abrasive paper for this. You cannot obtain
strong, durable glued joints in any other way.
The fuselage openings are factory-cut, including those for the glazing panels, cooling air slots
and so on. Other holes also have to be drilled, but this is done during the course of construction.
Where parts have to be glued inside the fuselage it is best to apply the adhesive on a length of
hardwood strip or similar tool. To prevent fuel absorption, all wooden parts must be sealed before being installed, e.g. by applying cyano to the surfaces.
It is important to trim the front and rear fuselage sections carefully to obtain a close fit.
The top (inside) surface of the bottom area of the front fuselage section (1) must be sanded flat,
especially at the centre seam; the same applies to the underside of the tongue which projects
forward at the bottom of the rear fuselage section (2), to which the front skid bar is attached. Cut
the plywood reinforcement (12) to final size and sand it to an angle at the rear as shown. Glue
this reinforcement to the underside of the projecting tongue, with its rear edge resting against
the step in the fuselage floor. The sides of the reinforcement must then be bevelled and the
shape of the tongue adjusted until the front fuselage section rests snugly on it. When you are
satisfied, drill 3.2 mm Ø holes for the skid mounting screws through the reinforcement and the
tongue, holding the drill exactly vertical.
Tape the front and rear fuselage sections together and mark the position of the two holes for the
skid mounting screws on the front section (1) working from the inside. Drill the holes 3.2 mm Ø.
1.1.2 Preparing the mechanics components
We assume that the mechanics to be installed in the model are already assembled and installed
in a completed “STARLET 50” model helicopter. In this case the following modifications have to
be carried out prior to installing the system in the fuselage:
• Remove the main rotor from the mechanics, followed by the collective pitch compensator, the
cabin fairing, the tail boom and the tail boom braces.
• Remove the tail rotor from the tail boom, at the same time undoing the clamping screws from
the tail rotor coupling and withdrawing the tail rotor drive shaft (steel rod, 2 mm Ø). Remove
the drive shaft from the tail boom from the front end and remove from it the quick-release
coupling sleeve and collet (these parts are required later).
• Remove the silencer from the motor; the compact silencer, Order No. 2272, is fitted in its
place, but it should not be installed at this stage and is supported against the mechanics
using the silencer console (4450.149), which is available separately as an accessory.
• Remove the complete canopy from the front end of the mechanics, including the mounting
brackets 1291.21A.
• Remove the skid landing gear.
• Remove the fueltank including parts 1291.21A which act as tank supports.
• Remove the contents of the RC box (receiver, battery etc.), then the RC box itself.
7