Download (PDF 6.1 MB)
Transcript
6 Installation See table 8 for the Friction Loss Equivalent in piping and fittings. 4 Example: When you end up using 3 x 45° -elbows and the concentric roof terminal, then the total venting length may not exceed 68 ft. (20.72 m). 3 × 45°-elbow = 3 x 4 ft. (1.22 m) = 12 ft. (3.66 m) concentric roof terminal 4"/6" = 20 ft. (6.10 m). 3 Total friction loss equivalent =32 ft. (9.76 m) 2 Total venting length for this example is: GB162-80 kW/100kW = 100 ft. (30.48 m) - 32 ft. (9.76 m) = 68 ft. (20.72 m) each for the intake and exhaust piping. 1 NOTICE ▶ The minimum covering wall thickness is 1" (25.4 mm). The maximum covering wall thickness is 16" (406 mm). ▶ For direct venting properly reassemble and reseal the vent and air-intake systems. 6720645916-101.1N Fig. 32 Vertical concentric venting system (sealed combustion) [1] [2] [3] [4] exhaust 4" (100 mm) intake 4" (100 mm) 12" (300 mm) over max. snow level or 24" (600 mm) whichever is greater 10"- 0" MIN (250 mm - 0 mm MIN) Do not exceed the total equivalent venting length of 100 feet (30,480 mm) maximum requirement each for the intake and exhaust piping. NOTICE ▶ Appliance input rates are based on minimum vent length operation. Longer vent lengths (up to maximum) will reduce the input proportionally. Equivalent Friction losses feet m 45° elbow 4", PVC, CPVC 4 1.22 90° elbow 4", PVC, CPVC 7 2.13 4" plastic pipe per foot, PVC, CPVC 1 0.30 parallel vent kit 2 0.61 concentric PVC terminal 4"/6" (100/150 mm) 20 6.1 45° elbow 4" (100 mm), PolyPro Elbow 7.2 2.2 45° elbow 4"/6" (100/150 mm), PolyPro Elbow 3.7 1.14 90° elbow 4" (100 mm), PolyPro Elbow 11.8 3.6 90° elbow 4"/6" (100/150 mm), PolyPro Elbow 5.6 1.72 4" (100 mm) PolyPro Pipe per foot 3.3 1.0 concentric 4"/6" (100/150 mm), PolyPro Pipe per foot 3.3 1.0 4" (100 mm) PolyPro Flex pipe per foot 6.9 2.1 parallel PolyPro Wall terminal 4" (100 mm) 13.8 4.2 concentric PolyPro Wall terminal 4"/6" (100/150 mm) 20.3 6.2 concentric PolyPro Roof terminal 4"/6" (100/150 mm) 26.0 7.9 PolyPro Roof terminal Flex Chimney Cap 3.3 1.0 CAUTION: ▶ Vent connectors serving appliances vented by natural draft shall not be connected into any portion of mechanical draft systems operating under positive pressure. At the time of removal of an existing boiler, the following steps shall be followed with each appliance remaining connected to the common venting system placed in operation, while the other appliances remaining connected to the common venting system are not in operation: a) Seal any unused openings in the common venting system. b) Visually inspect the venting system for proper size and horizontal pitch and determine there is no restriction, leakage, corrosion and other deficiencies which could cause unsafe condition. c) Place in operation the appliance being inspected. Follow the lighting instructions. Adjust thermostat so appliance will operate continuously. d) Test for spillage at the draft hood relief opening after 5 minutes of burner operation. Use the flame of a match or candle, or smoke from a cigarette, cigar or pipe. e) Any improper operation of the common venting system should be corrected so the installation conforms with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 and/or CAN/CSA B149.1, Natural Gas and Propane Installation Code. When resizing any portion of the common venting system, the common venting system should be resized to approach the minimum size as determined using the appropriate tables in Part 11 of the National Fuel Gas Code, ANSI Z223.1/NFPA 54 and/or CAN/CSA B149.1, Natural Gas and Propane Installation Code. Table 8 Friction Loss Equivalent in piping and fittings 22 Logamax plus GB162-80 kW / 100 kW – 7746800103 (2014/10)