Download EB-G50 - Altehandys.de

Transcript
ORDER NO. OMTD030725C8
Personal Cellular Telephone
EB-G50
900 MHz
Frequency Range
TX/RX Frrequency
Separation
RF Channel
1800 MHz
1900 MHz
TX: 880 MHz –
915 MHz
TX: 1710 MHz –
1785 MHz
RX: 925 MHz –
960 MHz
RX: 1805 MHz –
1880 MHz
45 MHz
95 MHz
80 MHz
374
300
1850 MHz –
1990 MHz
200 kHz
Bandwidth
Number of RF
174
Channels
Speech Coding
Full Rate / Enhance Full Rate
Operating
-10 °C – +55 °C
Temperature
Type
Class 4 Handheld
Class 1 Handheld
Class 1 Handheld
RF Output Power
Max. 32 dBm
Maz. 29 dBm
Max. 29 dBm
Moduration
GMSK
WAP
WAP 1.2.1
Connection
8 ch / TDMA
Voice digitizing
13 kbps RPE-LTP / 13 kbps ACLEP
Transmission speed
270.833 KBPS
Signal Reception
Direct Coversion
Antenna Impedance
(External Connector)
Dimensions
(Excluding antenna)
50
Height: 77 mm ∗ Width: 43 mm ∗ Depth : 16.9 mm
Weight
Max 65 g
Display
Header (1128 x 12 pix)+Body (128 x 96 pix) Bottom (128 x 16 pix)
2 LED for the LCD (Blue Light)
Illumination
6 LED for the keypad (Blue Light)
Keys
18 Physical Keys, 2 Way Navi-Key
SIM
3 V Plug-in Only
External DC Supply
Voltage
3.8 V
Battery
Standard Li-Ion 720 AHh
Standby Time
78.3-230 Hrs (∗)
Talk Time
1.6-7.9 Hrs (∗)
(∗)The network being used, SIM card usage, and the condition of the battery affect Battery life.
Y WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a
product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to
service or repair the product or products dealt with in this service information by anyone else could result in serious injury or
death.
R
ç 2003 Panasonic Mobile Communications Co., Ltd.
All rights reserved. Unauthorized copying and
distribution is a violation of law.
COMPANY LIABILITY
Every care has been taken to ensure that the contents of this manual give an accurate representation of the equipment.
However, Panasonic Mobile Communications Co., Ltd. accepts no responsibility for inaccuracies which may occur and reserves
the right to make changes to the specification or design without prior notice. The information contained in this manual and all
rights in any design disclosed therein, are and remain the exclusive property of Panasonic Mobile Communications Co., Ltd.
Other patents applying to material contained in this publication:
CP8 PATENTS
Comments or correspondence concerning this manual should be addressed to:
Panasonic Mobile Communications Co., Ltd.
600, Saedo-cho, Tsuzuki-ku, Yokohama, 224-8539, Japan
CONTENTS
1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
1.1.
1.2.
1.3.
Purpose of the Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Structure of the Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Servicing Responsibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
2. GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
2.1.
2.2.
2.3.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Handportable Main Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
3. OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
3.1.
3.2.
3.3.
3.4.
3.5.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Liquid Crystal Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Location of Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Concept of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Alpha Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
3.5.1. Charactor Set / Key Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
3.5.2. Editing Alpha Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
3.6. Features Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5
3.7. Incoming Call Line Identification (CLI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14
3.8. Public Man Machine Interface (MMI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14
3.8.1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14
3.8.2. Reading the Phonebook Memory Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14
3.8.3. Presentation of IMEI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14
3.8.4. Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14
3.8.5. Call Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14
3.8.6. Call Waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14
3.8.7. Call Line Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-15
3.8.8. Telecommunication Services used for Public MMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-15
3.8.9. Dial Divert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-16
3.8.10. Call bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-16
3.9. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-17
3.10. Important Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18
3.11. Security Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18
3.12. Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-19
i
4. TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
4.1.
4.2.
Tx Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
4.1.1. Frequency Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
4.1.2. Modulation Phase Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
4.1.3. Output RF Spectrum due to Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
4.1.4. Outout RF Spectrum due to Switching Transients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
4.1.5. Spurious Emissions at Antenna Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
4.1.6. Residual Peak Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
Rx Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
4.2.1. Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
5. TECHNICAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
5.1.
5.2.
5.3.
5.4.
5.5.
5.6.
RF Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
5.1.1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
5.1.2. RF Function Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
5.1.3. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3
Baseband Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
5.2.1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
5.2.2. Digital Baseband Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7
5.2.3. Kypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-8
5.2.4. Subcarrier Identity Module (SIM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-8
5.2.5. CPU Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-9
5.2.6. LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-9
5.2.7. Real Time Clock (RTC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-9
Audio System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-10
5.3.1. Voiceband Baseband Codec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-10
5.3.2. Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-11
5.3.3. Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-12
5.3.4. Loud Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-12
Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-12
Power Management System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-13
5.5.1. Power System Ship . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-14
5.5.2. Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-14
5.5.3. Power On / Off Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-15
5.5.4. Voltage Regulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-15
Battery Charging and Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-16
5.6.1. Charging Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-16
5.6.2. Deeply Discharged Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-16
6. DISASSEMBY / REASSEMBY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
6.1.
6.2.
6.3.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
6.1.1. Call Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
Disassemby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
Reassemby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-8
ii
7. REPAIR PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
7.1.
7.2.
7.3.
7.4.
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
Lead Free (PbF) solder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
External Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
7.3.1. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
Test Equipment Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-5
7.4.1. Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-5
8. SOFTWARE DOWNLOARD & ADJUSTMENT PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1
8.1.
8.2.
8.3.
Service Software Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1
MMI Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-3
Adjustment Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-4
8.3.1. Equipment Setting for TX/RX Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-4
8.3.2. Main Subjects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-4
8.3.3. Test Operation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-5
8.3.4. Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-11
9. REPLACEMENT PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1
9.1.
9.2.
9.3.
Case and Cover Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1
Main PCB Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-3
MMI (Keyboard) PCB Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-4
10. BLOCK DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-1
10.1. Block Diagram of Base Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-1
10.2. Block Diagram of RF Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-2
11. CIRCUIT DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-1
11.1. Circuit Diagram of RF Band-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-1
11.2. Circuit Diagram of RF Band-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-2
11.3. Circuit Diagram of GSM Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-3
11.4. Circuit Diagram of Voiceband, Baseband and Codec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-4
11.5. Circuit Diagram of Power Management System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-5
11.6. Circuit Diagram of Memory & SIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-6
11.7. Circuit Diagram of Audio 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-7
11.8. Circuit Diagram of Audio 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-8
11.9. Circuit Diagram of User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-9
11.10.Circuit Diagram of Key Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-10
12. LAYAOUT DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-1
12.1. Main PCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-1
iii
1. INTRODUCTION
WARNING
The equipment described in this manual contains polarised capacitors utilising liquid electrolyte. These devices are entirely safe provided
that neither a short-circuit nor reverse polarity connection is made across the capacitor terminals. FAILURE TO OBSERVE THIS WARNING
COULD RESULT IN DAMAGE TO THE EQUIPMENT OR, AT WORST, POSSIBLE INJURY TO PERSONNEL RESULTING FROM
ELECTRIC SHOCK OR THE AFFECTED CAPACITOR EXPLODING. EXTREME CARE MUST BE EXERCISED AT ALL TIMES WHEN
HANDLING THESE DEVICES.
Caution
The equipment described in this manual contains electrostatic devices (ESDs). Damage can occur to these devices if the handling
procedures described in Section 4 are not adhered to.
Caution
This equipment may contain an internal battery in addition to the external battery packs. These batteries are recyclable and should be
disposed of in accordance with local legislation. They must not be incinerated, or disposed of as ordinary rubbish.
1.1. Purpose of the Manual
This Service Manual contains the information and procedures required for installing, operating and servicing the Panasonic
GSM Personal Cellular Mobile Telephone system operating on GSM Digital Cellular Networks.
1.2. Structure of the Manual
The manual is structured to provide service-engineering personnel with the following information and procedures:
1. General and technical information - provides a basic understanding of the equipment, kits and options, together with detailed
information for each of the major component parts.
2. Installation and operating information - provides instructions for unpacking, installing and operating the equipment.
3. Servicing information - provides complete instructions for the testing, disassembly, repair and reassembly of each major
component part. Step-by-step troubleshooting information is given to enable the isolation and identification of a malfunction,
and thus determine what corrective action should be taken. The test information enables verification of the integrity of the
equipment after any remedial action has been carried out.
4. Illustrated parts list - provided to enable the identification of all equipment components, for the ordering of spare /
replacement parts.
1.3. Servicing Responsibilities
The procedures described in this manual must be performed by qualified service engineering personnel, at an authorized
service centre.
The service engineering personnel are responsible for fault diagnosis and repair of all equipment described in this manual.
– 1–1 –
2. GENERAL DESCRIPTION
2.1. General
This section provides a general description and kit composition details for the GSM Handportable Telephone System
and optional kits.
2.2. Features
The Panasonic Telephone Model G50 is a high performance, small, light, handset for business and domestic use.
The following features are provided:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Dual Codec, which includes Full Rate and Enhanced Full Rate (EFR) Speech Codec.
Triple Band, E-GSM 900 and PCS 1800 /1900 operation.
Tegic T9 Text Entry.
Voice Ringer.
Desktop handsfree function comprising integral echo cancellation and noise suppression.
Wireless Application Protocol (WAP) Browser.
Backup Battery.
Downloadable polyphonic melody ring tones.
Clock, Calculator and Currency Converter.
2.3. Handportable Main Kit
Battery
Main Unit
Travel Charger
Figure 2.1: Handportable Main Unit Kit Contents
– 2–1 –
3. OPERATING INSTRUCTIONS
3.1. General
This section provides a brief guide to the operation and facilities available on the telephone handset.
Refer to the Operating Instructions supplied with the telephone for full operational information.
3.2. Liquid Crystal Display
The telephone handset has a graphical chip on glass display. The following icons are available:
Status
Figure 3.1: Liquid Crystal Display
Icon
Description
The received signal strength indication – No CHPS;
: Line1;
: Line2
Indicated the battery level / Low Battery:
Displayed when the user is registered to a non-home network-roaming
Displayed when call divert is enabled – No CPHS;
Line2
: Line1;
: Line2;
: Line1 &
Displayed when phone lock is enabled
Displayed when an unread message is store or lights when message area is full
Voice mail icon
Indicated alarm is set
Displayed when vibration alert is enable
Displayed when all tones or ring volume is off
GPRS ON indication
GPRS ON and attached indication
Context active and coverage lost/searching
– 3–1 –
3.3. Location of Controls
Receiver
Phone Jack
Display
Charger Connection
The Phone Jack can be used as data transmission port to perform download and test tasks.
– 3–2 –
3.4. Concept of Operation
There is a close relationship between the Select keys, Navigation key and display.
Main Display
Left Hand Selection Area
Navigation key
Right Hand Selection
Soft Key
Send and answer Key
Power / End Key
Navigation Key: Moving up and down through the options in the display area. In idle mode, pressing
to enter Own Menu. Own menu is a short cut to access your favourite menu. You can set it the personalize.
Soft keys: Perform the functions indicated by text shown on the LCD screen. In idle, long press left soft
key to enter Messages, long press right soft key to enter Profile Mode List.
Numeric key pads: Long Press
to enter a "+" or "P". When you need to dial an extension number,
dial the phone number firstly then longer press
to add a "P" and enter the extension number.
Send/Answer Key: Make a call or answer a call, In mode, check the last dialled list.
Power/End Key: To end a call return to idle mode, return to previous menu or reject an
incoming call, Long press it to switch the phone on/off.
In idle, long press to active Browser.
In idle, long press to switch the Mute Mode on and off.
– 3–3 –
3.5. Alpha Entry
3.5.1 Character Set / Key Assignments
Alpha entry is used to enter alphanumeric characters in to the Phonebook, Short Message and Greeting
Message areas.
Alphabetic, small / capital letter mode:
Key
1.
2.
3.
4.
5.
6.
7.
8.
9.
11.
12.
13.
14.
15.
1
1
/
(
)
<
=
>
2
a/A
b/B
c/C
2
ä
à
ç
3
d/D
e/E
f/F
3
é
è
4
g/G
h/H
i/I
4
ì
5
j/J
k/K
l /L
5
6
m/M n/N
o/O
6
ö
ñ
7
p/P
q/Q
r/R
s/S
7
ß
8
t/T
u/U
v/V
8
ü
ù
9
w/W x/X
y/Y
z
9
æ
ø
å
∆
Θ
Λ
Ξ
Π
Σ
Φ
Ψ
Ω
.
,
?
!
+
-
:
¿
¡
"
'
;
_
13.
14.
15.
16.
;
_
∗
∗
0
Γ
Space 0
#T
9
%
10.
&
~
ò
Space #£$
§
@
on/off
mode
T9 mode
Key
1.
2.
3.
4. 5.
6.
space
1
/
(
<
=
∗
Γ
∆
Θ Λ
Ξ
,
?
+
$
T9 Editor
Tegic
Sequence
mode
TC
T9 on
T9 Abc T9 abc
T9 ABC 123 BPMF
Stroke_TC
SC
T9 off
Abc
ABC
Stroke_SC
0.
#
£
9.
10. 11.
12.
>
%
~
&
Π
Σ
Φ
Ψ
Ω
-
:
¿
¡
"
¥
@ ¥
§
1.
2.
)
!
7. 8.
'
T9 Editor Sequence
Key
Send
abc
3.
4.
5.
123 Pin Yin
6.
n
Key 1, 2, 3, 4, 5, 6, 7, 8, 9, 0 long press provides corresponding numbers.
n
All other keys are used for Tegic T9 intelligent text mapping.
n
TC: Traditional Chinese; SC: Simplified Chinese; BPMF: Input method of traditional Chinese
3.5.2 Editing Alpha Entry
Pressing will move the cursor up or down one line. Pressing will move the cursor left or right one character.
When the cursor is moved over a character and another key pressed will insert the new character.
Pressing
will delete the character to the left of the character.
– 3–4 –
3.6. Features Structure
Feature Set Listing
1 Telephone Functionality
Display and Lighting
LCD Display
Received Signal Strength Indication
Battery Status Icon
Call Processing Signal Indication
Dialled Number Indication
Last Dialed Digit Clear/Entire Line Clear
Own Telephone Number Indication
Service/No Service Indication
Country/PLMN Indication
Service Provider Indication
Roaming Indication
SMS Ariving Indication
SMS Overflow Indication
Vibration Mode Status Indication
Lock Status Indication (Keypad Lock)
Greeting Message Editing
Power On/Off Animations
Clock Alarm Indication
Show Time & Date
Line Service Indication
GPRS Status Indication
Back-lighting
LCD Backlight
Keypad Backlight
Incoming Call Backlighting
Security
Access Codes
PIN
– 3–5 –
PUK
PIN2
PUK2
Phone Code
PIN Check
Change PIN
FDN Mode (On/Off)
ME Personalization
Network lock
Network Subset Lock
Service Provider Lock
Corporate Lock
SIM Lock
Custom IMSI
Multiple Lock
Sound Settings
Ring Tone/Melody (20 predefined, 5 composed, X download)
Ring Volume Control (1-5)
Alert Type
Ring Only
Vibration Only
Vibration and Ring
None
Keypad Tone
On (Individual Key Sounds: DTMF tones)
Off (No Keypad Sound)
Service Tone
Network Found
Warning Tones (for low battery, etc.)
Phone Parameters
Greeting Message
Own Number
Language
Any-key Answer (On/Off)
Auto Answer (On/Off)
Brightness (Off, Low, Medium, High, Maximum)
Redial
– 3–6 –
Reset Setting to Default
Hot Key Dial (On/Off)
Key 1 to 9 assigned to the Phone-number in SIM or
Mobile records from 1 to 9 according to the selection of
My Phonebook and press <Send> to dial out
Clock Setting
Set Time
Set Date
Display Format
Languages/Fonts/Bitmaps
Fonts & Bitmaps
Character Set Definition, mapping & Decoding
Text String Translation For all languages
Full GSM Character Set
Network Service (Requires Carrier Protocol Stack Support)
Call Diverting
Divert Always
Busy
No Reply
Unreachable
Cancel All
Call Barring
All outgoing Calls
Outgoing International Calls
Outgoing International Calls, Except Home
All Incoming Calls
All Incoming Calls When Roaming
Cancel All
Change barring Password
Caii Waiting
Enable
Disable
Network Selection
Network Select
Auto/Manual Selection
Preferred List
Band Select
– 3–7 –
Line Identification
Calling Line Identification Presented (CLIP)
Calling Line Identification Restricted (CLIR)
Connected Line Identification Restriction (COLP)
Connected Line Identification Restriction (COLR)
In-Call Menu (Requires Protocol Stack Support)
Call on Hold/Swap
Answer Second Call
Display of Change Advice Information
Multiple Call
Having Private Conversion With One Participant
Dropping One Participant
SMS (Requires Carrier and Stack Support)
Enhanced Message Service
Bitmap (15)
Melody for ringer tone (10)
UCS2, 8 Bit Encoding support
Read Message
Header Display
Message Number
Message Status
View Message
Sender's Phone Number (If Sent)
Date And Time Message Received
Message Text
EMS Picture Message
EMS Sound Message
Text Reply
Change SMS Center Number
Send Message
Save Message
Delete Message
Extract Number From Message
Recognition of phone number
Send (Resend Message Already Sent)
Edit Message
Write Messages
– 3–8 –
Send
Insert Predefined Text
Insert Picture/Melody (EMS MO)
Save and Send Message
Save Only
Auto capital letter in the beginning of string input
Predefined Text (15)
Edit Preset Message
Clear Preset Message to Empty
Setup
Service Center Number
Store SMS Center Number
Edit SMS Center Number
Message Type
Reply Path
Status Report
Validity Period
Broadcast
Read Messages
Save Messages
Receive (Enable/Disable)
Channel List (scan up to 5 channels in parallel)
Enter New Channel
All Channels (Enable/Disable)
Language Preference
Call Records
Missed Calls (Number: 20)
Display Number, Name (if available), Date and Time
Edit, Dial or Save Number
Delete Number From List
Received Calls (Number: 20)
Display Number, Name (if available), Date and Time
Edit, Dial or Save Number
Delete Number From List
Dialled Calls (Number: Minimum to 10)
Display Number, Name (if available)
Edit or Save Number
– 3–9 –
Redial Number
Delete Number
Call Time
Last Call Time
Total Sent
Total Received
Reset Times
Call Cost (Requires Protocol Stack Support)
Last Call Cost
Total Cost
Max Cost
Reset Counters
Set Max Cost
Price/Unit
GSM 2.30 MMI and GSM 2.90 USSD
2 Optional Network Service (Requires Carrier and Protocol Stack Support)
SIM Toolkit
Class 1 (SIM Content Update)
Class 2 (SMS Proactive SIM)
Class 3 Send USSD
3 Applications
Mobile Phonebook
7 fields available
Name
Mobile phone number
Home phone number
Office phone number
Groups
- No Group
- Friends
- Colleagues
- Family
- Others
- VIP
Image Caller ID
– 3–10 –
Melody
Mobile Phonebook Menu
Edit Phonebook Number and Name
Erase Phonebook Number and Name
Speed Dialling (1-9) if mobile phonebook selected as preferred
phonebook
Copied one or all to SIM Phonebook
SIM Phonebook
Phonebook Name and Number Storage
ADN (Depends on SIM, Max 255)
FDN (Number of entries Max 50)
SIM Phonebook Menu
Edit Phonebook Number and Name
Erase Phonebook Number and Name
Speed Dialling (1-9) of SIM phonebook selected according to
preferred phonebook
Copied one or all to Mobile Phonebook
Own Number
Service Dialling Number
Dialling From Phonebook
Calculator
Appointment List
Data/Time with Alarm-like Reminder
Currency Converter
World Clock
Select cities
Set Time
Set Date
Daylight Saving On/Off
Time Format
Date Format
Melody Composer (Max. 5)
Wall Paper in Idle Mode (20 default, X download)
Picture Manager :
Manage picture list
The picture can be used as wallpaper in idle screen or picture link
20 128x80 predefined pictures (10 idle screen + 10 picture link)
– 3–11 –
X downloaded; X depends on the media library's size; The size of a downloaded
picture can be variable.
Melody manager (20 default. 5 composed, X downloaded)
Manage picture list
20 predefined melodies
5 user composed melodies
X downloadable, X depends on the Media Library size.
Games (WGE)
Game 1
Game 2
Game 3
4 Miscellaneous
Battery Management
Low Battery Warning
Power Off Indication
Charging Status
Accessory Support
Alpha-numeric Input
Alpha Mode
Numeric Mode
T9 Smart input version 5.0
English: Predictive input
Chinese:
1. Bopomofo (for Traditional Chinese)
2. Pinyin (for Simplified Chinese)
3. Stroke (for Traditional Chinese)
4. Stroke (for Simplified Chinese)
5 Additional Services
OTA Download via WAP
Bitmap Picture
JPEG picture
Melody for ring tone
WAP Browser (Openwave 6.1)
Home
Bookmark (10 available)
Profiles (5 available)
Connection setting
– 3–12 –
- Homepage
- Connection Type
- Connection Security
- IP Address
- Linger Time
(CSD Bearer)
- Dial number
- Data Call type
- User Name
- Password
(GPRS Bearer)
- APN
- User Name
- Password
- Authentication
– 3–13 –
3.7. Incoming Call Line Identification (CLI)
When a call is received the last eight digits of the CLI information is matched with the phonebook.
Therefore an incoming call could be matched to the wrong phonebook entry.
3.8. Public Man Machine Interface (MMI)
3.8.1. General
It is possible to operate all GSM telephones in the same way using the Public MMI. The following
operations will work with all GSM telephones. However, this information is restricted to those
operations supported by the telephone.
The * and # in the following procedures should be replaced by
and <END> should be replaced with
and
keys
and
respectively. Also <SND>
3.8.2. Reading the Phonebook Memory Location
# <MEMORY LOCATION>
Leading zeros can be left out of the location number, e.g. 007 can be 7.
3.8.3. Presentation of IMEI
*#06#
3.8.4. Security
Change PIN
* * 0 4 * <OLD PIN> * <NEW PIN> * <NEW PIN> #
Change PIN2
* * 0 4 2 * <OLD PIN2> * <NEW PIN2> * <NEW PIN2> #
Unblock PIN
* * 0 5 * <PIN UNBLOCKING KEY> * <NEW PIN> * <NEW PIN> #
Unblock PIN2
* * 0 5 * <PIN2 UNBLOCKING KEY> * <NEW PIN2> * <NEW PIN2> #
3.8.5. Call Hold
Place a Call on Hold
2 <SND>
Recall a Held Call
2 <SND>
Make a Second Call
<TELEPHONE NUMBER>?<SND>
Swap between two Held Calls
2 <SND>
End Held Call
0 <SND>
End Active Call
1 <SND>
Reject Incoming Call
0 <SND>
3.8.6. Call Waiting
Enable Call Waiting
*43 * <SND>
Disable Call Waiting
#43 * <SND>
Call Waiting Status
* # 4 3 * # <SND>
– 3–14 –
3.8.7. Call Line Identification
Feature
Service Code
Calling Line Identification Presentation (CLIP)
30
Calling Line Identification Restriction (CLIR)
31
Connected Line Presentation (CLOP)
76
Connected Line Restriction (CLOR)
77
Enable
* <SERVICE CODE> * # (SND>
Disable
# <SERVICE CODE> * # (SND>
Temporary Suppress Identification
# 31 # <TELEPHONE NUMBER> <SND>
Temporary Display Identification
* 31 # <TELEPHONE NUMBER> <SND>
3.8.8. Telecommunication Services used for Public MMI
Teleservice
Service
MMI Service Code
All teleservices
10
Telephony
11
All data teleservices
12
Facsimile services
13
Short Message Service (SMS)
16
All teleservices except SMS
19
Voice group service
17
Bearer Service
Service
MMI Service Code
All bearer services
20
All asynchronous services
21
All synchronous services
22
All data synchronous services
24
All data asynchronous services
25
All dedicated packet access
26
All dedicated PAD access
27
– 3–15 –
3.8.9. Dial Divert
Call Divert Type
Service Code
Divert all calls
21
Divert all calls if busy
67
Divert all calls if no reply
61
Divert if not reachable
62
Set Call Bar
* * <SERVICE CODE> * <FORWARD TELEPHONE NUMBER> *
(Except "No Reply")
<TELECOMMUNICATION SERVICE> # <SND>
Set "No Reply" Call Bar
* * <SERVICE CODE> * <FORWARD TELEPHONE NUMBER> *
<TELECOM' SERVICE> * <TIME TO RING (sec)>#<SND>
# # <SERVICE CODE> * <TELECOMMUNICATION SERVICE> * #
Clear
<SND>
* * # <SERVICE CODE> * <TELECOMMUNICATION SERVICE> * #
Status
<SND>
Clear all Call Diverts
# # 002 #
3.8.10. Call Bar
Call Bar Type
Service Code
All outgoing calls
33
Outgoing International calls
331
Outgoing International calls except those to the PLMN
332
All incoming calls
35
Incoming international calls when roaming
351
Set
* <PASSWORD> * <TELECOMMUNICATION SERVICE> # <SND>
Clear
# <TELECOMMUNICATION SERVICE> # <SND>
Status
# <TELECOMMUNICATION SERVICE> # <SND>
Clear all Call Bar Type
# 330 * <PASSWORD> # <SND>
Change Call Bar
* * 03 * * <OLD PASSWORD> * <NEW PASSWORD> * <NEW
Password
PASSWORD # <SND>
– 3–16 –
3.9. Troubleshooting
The user is given the following information and advised to contact the dealer if the problems persist:
Problem
Cause
Remedy
Telephone will not
Check that the battery pack is fully
switch on
charged and correctly connected to the
telephone.
Extremely short battery
The network in use and the
Avoid areas of poor reception. Ensure
life for a new battery
condition of the battery pack
batteries fully charged.
pack
can affect battery life.
Short battery life for an
The battery pack was worn
old battery pack
out.
The battery level
If a battery is deeply
Leave to charge for several minutes in
indicator
discharged it will take a
temperatures between +5 °C and
short time before there is
+35 °C
does not light when
charging
Replace with a new one.
sufficient power in the
telephone to light the battery
level indicator
Calls cannot be made
.
The telephone is locked.
Unlock the telephone.
Outgoing calls are barred.
Disable the outgoing call barring
(Phone Option: Security: Call bar).
The telephone is not
Move to a coverage area and operate the
registered to a network.
telephone after it has registered with a
network.
Calls cannot be made
Check that SIM supports Fixed Dial
from Fixed Dial Store
Check if the Fixed Dial is switched on
(Phone Operation: Security: Fixed Dial).
Check the telephone number is stored in
the Fixed Dial.
Calls cannot be received
The telephone is not
Switch the telephone on.
switched on.
Incoming calls are barred.
Disable the incoming call barring
(Phone Option: Security: Call Bar).
The telephone is not
Move to a coverage area and operate the
registered to a network.
telephone after it has registered with a
network.
Emergency calls cannot
User's phone is not in a
Check that the antenna symbol
be made
GSM coverage area.
displayed. Move to a coverage area and
is
operate the telephone when the antenna
symbol is displayed.
Telephone numbers
The telephone is locked.
Unlock the telephone.
Cannot be recalled
Fixed Dial is switched on
Switched off Fixed Dial
(Phone Option: Security: Fixed Dial).
– 3–17 –
3.10. Important Error Messages
The following table is a list of error messages that may occur during use of the telephone, with a
description and suggested course of action:
Error Message
Explanation / Remedy
Area not Allowed
Roaming in the selected area is not allowed.
Network not allowed
Roaming with the selected network is not allowed.
Security Failure
The network has detected authentication failure because the SIM is not
registered with that network. Contact the Service Provider.
SIM Blocked
The SIM is blocked because the wrong PUK has been entered 10 times.
Contact the Service Provider.
SIM Error
The telephone has detected a problem with the SIM. Switch the telephone
off and then back on. If the message does not disappear, contact the
Service Provider.
Message Rejected
A message has been received but the message store is full. To receive
Store Full
messages, delete some of the currently stored messages.
PIN2 Invalidated
The PIN2 is blocked permanently because the wrong PUK2 has been
entered 10 times. Services controlled by PIN2 cannot be used. Contact the
Service Provider.
Warning Store Full
The message area is full. New messages cannot be stored unit some of
Continue?
the currently stored messages are deleted.
3.11. Security Codes
Code Type
Personal Identification
Number or Digits
4 to 8
Number (PIN)
PIN2
Description
Controls SIM security. Supplied by the service
provider.
4 to 8
Controls memory security. Supplied by the service
provider.
PIN/PIN2 Unblocking
Supplied by the service provider.
Key
(PUK/PUK2)
8
Used to unblock PIN and PIN2. A PIN or PIN2 will
become blocked if the wrong PIN or PIN2 is
entered three times. When the blocked PIN or PIN2
is unblocked, a new PIN or PIN2 must be entered.
If the wrong PUK or PUK2 is entered 10 times, the
cursor SIM will be unusable.
Password
4
Controls the call bar function. If the wrong password
is entered three times, this service will be revoked.
Supplied by the service provider.
Phone lock Code
4 to 8
Controls telephone security.
– 3–18 –
3.12. Glossary of Terms
Term
DTMF
GSM
Home network
Hot Key Dial
Phone Lock code
Message Centre
Network operator
Password
PIN
PIN2
PUK/ PUK2
Registration
Roaming
Definition
Dual Tone Multiple Frequency tones. The numeric keys 0 to 9, and * and # will
generate different DTMF tones when pressed during conversation. These are
used to access voice mail, paging and Home banking services.
Global System for Mobile communications. The name given to the advanced
digital technology that the telephone uses.
The GSM network on which subscription details are held.
Hot Key Dial allows quick access to numbers stored in the Phonebook of Service
Dial Number list. The source of the Hot Key Dial may be defined by the user or
preprogrammed by the Service Provide. It is most likely to be preprogrammed to
the Service Dial Numbers by the Service Provider.
Used for security of the telephone.
Where messages are sent before they are forwarded on to their destination. The
Message Centre telephone number may be programmed into the SIM or
supplied by the service provider.
The organization responsible for operating a GSM network.
Used for the control of the call bar function. Supplied by the service provider.
Personal Identification Number used for SIM security. Supplied by the service
provider.
Personal Identification Number used for the control of Fixed Dial Memory and
call charge metering.
Supplied by the service provider.
PIN/PIN2 Unblocking Key. Used to unblock the PIN/PIN2. Supplied by the
service provider.
The act of locking on to a GSM network. This is usually performed automatically
by the telephone.
The ability to use the telephone on networks other than the Home network.
Service Dial Numbers Service Dial Numbers are predefined numbers that allow the user to access a
set of special services provided by the Service Provider. For example billing
information or access to Voice Mail.
Service provider
The organization responsible for providing access to the GSM network.
SIM
Supplementary
Service
Wild numbers
Subscriber Identification Module. A small smart-card which stores unique
subscriber and user-entered information such as Phone Book, Fixed Dial
Memory and short messages. Supplied by the service provider.
Network-controlled GSM functions supported by the telephone. Supplementary
services may only be available on a subscription bases.
Spaces in a stored telephone number. When the telephone number is recalled
pressing a numeric key will fill in a space. This can be used to restrict dialing to a
specific area.
– 3–19 –
4. TECHNICAL SPECIFICATIONS
4.1. Tx Characteristics
All data is applicable to E-GSM 900 and GSM 1800 except where stated.
4.1.1. Frequency Error
±0.1 ppm max., relative to base station frequency.
4.1.2 Modulation Phase Error
RMS: Equal to or less than 5 °
Peak: Equal to or less than 20 °
4.1.3. Output RF Spectrum due to Modulation
Offset from Centre Frequency (kHz)
±100
±200
±250
±400
±600 to 1800
Maximum Level Relative to Carrier (dB)
+0.5
–30
–33
–60
–60
4.1.4. Output RF Spectrum due to Switching Transients
Maximum Level (dBm)
Offset from Centre Frequency (kHz)
E-GSM 900
±400
±600
±1200
±1800
–19
–21
–21
–24
Measurement conditions for output RF spectrum measurements:
Frequency Span
0 Hz
Measurement Bandwidth:
30 kHz
Video Bandwidth:
30 kHz (modulation)
100 kHz (switching)
Average (Modulation)
Over 200 burst
Peak Hold (Switching)
Over 10 burst
– 4–1 –
GSM 1800
–22
–24
–24
–27
GSM 1900
–22
–24
–24
–27
4.1.5. Spurious Emissions at Antenna Connector
Frequency
Filter
Approx
Limits(dBm)
Frequency Range
offset
100KHz to 50MHz
Bandwidth
-
50 to 500MHz
-
500MHz to 1GHz
1 GHz to 12.75 GHz
Excl. relevant TX band
E -GSM:880 to 915 MHz
DCS:1710 to 1785 MHz
-and the Rx bands
925 -960 MHz
1805 -1880 MHz
Relevant TX band:
E -GSM:880 to 915 MHz
DCS:1710 to 1785 MHz
0 to 1MHz
0 to 10MHz
>10MHz
>30MHz
(off trom edge
of relevant Tx
band)
Video B/W
10KHz
30KHz
100KHz
300KHz
100KHz
300KHz
100KHz
300KHz
3MHz
300KHz
1MHz
3MHz
E-GSM 900
GSM1800/1900
-36
-36
-36
-36
-36
-30
-30
-30
-36
-30(1.0 -1.710GHz)
-36(1.710 -1.785GHz)
-30(1.785 -12.75GHz)
1.8 to 6.0 MHz
> 6.0MHz
30KHz
100KHz
100KHz
300KHz
-36
-36
-36
-36
4.1.6. Residual Peak Power
Equal to or less than 70 dBc (BW = 300 kHz)
4.2. Rx Characteristics
4.2.1. Sensitivity
E-GSM 900 Full Rate Speech
The reference sensitivity performance in terms of frame erasure, bit error, or residual bit error rates (whichever is appropriate)
is specified in the following table, according to the propagation conditions.
Channels
Propagation
conditions
TU high
Tes t Limit Minimum
error rate
No of
%
samples
6.742*_
TCH/FS FER
Class lb (RBER) 0.42/_
Class ll (RBER) 8.33
Propagation
conditions
RA
Test Limit Minimum
error rate
No of
%
samples
8900
1,000,000 7.5
120,000
24000
Propagation
conditions
HT
Test Limit
Minimum
error rate
No of
%
samples
9.33
60000
Static Conditions
Test Limit
error rate
%
Minimum
No of
samples
0.122*_
0.41/_
2.439
164000
20,000,000
8200
The reference sensitivity level is < -102 dBm.
NOTE: 1 < _ < 1.6. The value of a can be different for each channel condition but must remain the
same for FER and class 1b RBER measurements for the same channel condition.
– 4–2 –
GSM 1800/1900 Full Rate Speech
The reference sensitivity performance in terms of frame erasure, bit error, or residual bit error rates (whichever is appropriate)
is specified in the following table, according to the propagation conditions.
Channels
TCH/FS FER
Class lb (RBER)
Class ll (RBER)
Propagation
conditions
TU high
Test Limit Minimum
error rate
No of
%
samples
4.478*_
0.32/_
8.333
Propagation
conditions
RA
Test Limit Minimum
error rate
No of
%
samples
13400
1,500,000
60,000
7.5
24000
Propagation
conditions
HT
Test Limit
Minimum
error rate
No of
%
samples
Test Limit
error rate
%
Minimum
No of
samples
9.333
0.122*_
0.41/_
2.439
164000
20,000,000
8200
30000
Static Conditions
The reference sensitivity level is < -102 dBm.
NOTE: 1 < _ < 1.6. The value of _ can be different for each channel condition but must remain the
same for FER and class 1b RBER measurements for the same channel condition.
– 4–3 –
Blocking:
Small MS level in dBµVemf( )
E-GSM 900
GSM 1800
Frequency
GSM 1900
FR ± 600 kHz to FR ± 800 kHz
70
70
70
FR ± 800 kHz to FR± 1,6 MHz
70
70
70
FR ± 1,6 MHz to FR ± 3 MHz
80
80
80
915 MHz to FR - 3 MHz
90
-
-
FR ± 3 MHz to FR 980 MHz
90
-
-
FR ± 600 KHz to FR ± 800 KHz
-
87
87
1785 MHz to FR - 3 MHz
-
87
87
835 MHz to < 915 MHz
113
-
-
> 980 MHz to 1000 MHz
113
-
-
100 KHz to < 835 MHz
90
-
-
> 1000 MHz to 12.75 GHz
90
-
-
100 KHz to 1705 MHz
-
113
113
> 1705 MHz to < 1785 MHz
-
101
101
> 1920 MHz to 1980 MHz
-
101
101
> 1980 MHz to 12.75 GHz
-
90
90
Measurement Conditions:
Wanted carrier is 3 dB above reference sensitivity.
Interferer is CW.
Spurious response exceptions:
Six exceptions are permitted IN band 915 - 980 MHz.
24 exceptions are permitted OUTSIDE band 915 - 980 MHz.
Intermodulation Characteristics
Interferer Level ( f1 & f2) dBm
-49
Interferer Frequencies ( f1 & f2 )
Wanted frequency= 2f1 - f2,
and [ f1 - f2] = 800 kHz
– 4–4 –
5. TECHNICAL DESCRIPTION
5.1. RF Overview
5.1.1. Introduction
■ General Specifications
The telephone is a Tri-Band product.
The transmit and receive bands for the mobile are given in the table below:
E-GSM 900
GSM 1800
PCS 1900
Tx
880 - 915 MHz
1710 - 1785 MHz
1850 - 1910 MHz
Rx
925 - 960 MHz
1805 - 1880 MHz
1930 - 1990 MHz
Other salient technical features are as follows:
E-GSM 900
GSM 1800
PCS 1900
RX Bandwidth
35 MHz
75 MHz
60 MHz
TX Bandwidth
35 MHz
75 MHz
60 MHz
Number of Channels
174
374
299
AFRCN (Channel Numbers)
0- 124
512-885
512-810
880.2 MHz
1710.2 MHz
1850.2 MHz
(Ch 975)
(Ch 512)
(Ch 512)
914.8 MHz
1784.8 MHz
1909.8 MHz
(Ch 124)
(Ch 885)
(Ch 810)
925.2 MHz
1805.2 MHz
1930.2 MHz
(Ch 975)
(Ch 885)
(Ch 512)
959.8 MHz
1879.8 MHz
1989.8 MHz
(Ch 124)
(Ch 885)
(Ch 810)
33.0 dBm
30.0 dBm
30.0 dBm
(Class 4)(PL 5)
(Class 1)(PL 0)
(Class 1)(PL 0)
5.0 dBm
0.0 dBm
0.0 dBm
(PL 19)
(PL 15)
(PL 15)
975-1023
1st TX Channel
Last TX Channel
1st RX Channel
Last RX Channel
Maximum TX Power
Minimum TX Power
– 5–1 –
ANTENNA SW
– 5–2 –
DCS
PCS
GSM
PC
DC
GSM
CX77314
Figure 5.1. : RF Function Block Diagram
TXVC
TLCPO
UCP
UVTUN
LNA1900I
LNA1800I
LNA900I
CP
DI
LOGE
LOGE
DI
CX74063
FrrcN PLL
DC
90
DC
T/
TXQ
TXQ
TXI-
TXI
FRE
DATA,CLK
DC
RXQ
RXQ
RXI
RXI
VTCXO
26MHz
5.1.2. RF Function Block
BASEBAND
5.1.3. Functional Description
■ Frequency Plan
The frequency plan is shown below:
TX Frequency Plan
TX Frequency
TX IF
TX RF LO
E-GSM 900
880.2 - 914.8MHz
88.46 - 114.35MHz
1459.59 -1543.725MHz
GSM 1800
1710.2 - 1784.8MHz
90.316 - 104.776MHz
1354.737 - 1414.482MHz
PCS 1900
1850.2 - 1909.8MHz
97.379 - 112.341MHz
1460.684 - 1516.606MHz
RXI
RX RF from
LNA
FVCO =
FRX
90°
90°
x2
3
FRX
2k
RXQ
Where k is 1 for low band and 2 for high band.
x1
Fractional-N
PLL
/3
FVCO
UHF VCO
x2
k = Frequency muliplier
101959A 2_020802
Figure 5.2. Receiver Block Frequency Plan
■ General
RF circuit design is built based on SKYWORKS-74063 direction conversion transceiver IC integrated by SAW filters,
power amplifier with control circuit, and Transmitter/receiver switch.
RF LO always requires external frequency sources with VCTCXO in VE2. And LO frequency is periodically re-tuning to
synchronize with cell or network.
■ Antenna
EB-G50 uses Helical-type antenna, which is most low-cost, monopole-like antenna. The antenna takes different
spacing to define bands of GSM, DCS and PCS.
– 5–3 –
■ Transceiver - - Transmitter
Antenna
Base-band
section
Power
Detector
TX IN I/Q
Coupler
PA gain
controller
3-wire bus
PAVAPC
+
–
TXVCO
TX IN
900
1800/1900
PFD
PA
UHF synthesizer
Figure 5.3. Transmitter block diagram
TX path is a translation loop architecture consisting of an IQ modulator, integrated high power VCO, offset mixer,
programmable divider, PFD, charge pump, and power amplifier with its control circuit.
The device consists of an In-phase and Quadrate (I/Q) modulator within a frequency translation loop designed to
perform frequency up-conversion with high output spectral purity.
Clock source is 26MHz VCTCXO external instead of XTAL function block active. VCTCXO is more stable over
extreme condition and current saving in standby mode.
– 5–4 –
■ Transceiver - - Receiver
RX LO
source from chip
Antenna
RF SAW
FILTER
RXIN
RXIP
900
T/R
Switch
&
Display
RXQN
RXQP
1800
1900
VGA
DCOC
LNA
Figure 5.4. Receiver block diagram
RX path is a direction down conversion architecture that eliminates the need for Intermediate Frequency (IF) components.
The device includes three bands integrated LNAS, a quadrate demodulator, baseband amplifier circuit with I/Q outputs
and three stages of DC-offset correction.
The DCOC correction loop ensures DC-offsets, generated in CX74063, do not overload baseband chain.
The receiver can be calibrated to optimize IP2 performance, which ensures limited baseband interfering signal amplitude.
The CX74063 also features an integrated, fully programmable, sigma-delta fraction-N synthesizer suitable for GPRS
multi-slot operation.
– 5–5 –
5.2. Baseband Overview
5.2.1. Introduction
The Baseband circuits of the phone are required to perform the following functions:
8 Equalization
8 Channel coding / decoding
8 Speech coding / decoding
8 Data Encryption
8 Layer 1, 2 and 3 software tasks
8 Man Machine interface (MMI)
8 System Interface
8 SIM Interface and Management
8 Audio and Tone Generation
8 Power supply and battery management
8 RF power control
8 Synchronization
8 Real time clock
VBAT
Keyboard
13MHz_BB
Keypad Data bus
BBCLK
Buffer
V_LED
Backlight
LED
Vibrator
GPIO12
CLKIN
BACKLIGHT
GPO22
USC Data Bus
VTCXO
TX/RX
Handfree input
GPIO6
RF Control Bus
R.F.
Block
HANDFREE IN
Address Bus
RTC
Crystal
SIM
Socket
32.768kHz
OSC
Memory
Flash/SRAM
(64MB / 16MB)
Data Bus
VMEM
SIM interface
V_LED
SIMVCC
TX IQ
GSM Processor
(AD6525)
RX IQ
Control Signal
LCD_PWR
LCD Module
White LED
DRV 4.5V
LDO 3.0V
LCD Control Bus
Charging control interface
EXTPWR
VINNOR P/N
MIC
VOUTNOR P/N
Receiver
TX/RX
Phone
Jack
Audio
Analog
Switch
VINAUX P/N
VOUTAUX P
PJ_FUNC_SEL
ADC/DAC
VoiceBand
&
BaseBand
Codec.
(AD6521)
A,V,B
serial Port
VCC
VCORE
VMEM
VMEM
VANA
VANA
Buzzer(L_SPK Mode)
VTCXO
Control /Data
Interface
YMU_AVCC
OverVoltage
Protect Circuit
Power
Jack
VRTC
GPIO 13
PJ_FUNC_SEL
VANA
Power
Management
(ADP6522)
RTC
Battery
Meledy IC
LDO 3.0V
Charging
Circuit
VCORE
HPOUT
Speaker
VCORE
VMEM
VRTC
SIMVCC
P MOSFET
VTCXO
VRTC
VSIM
VBAT
VBAT
Li-Ion
Battery
Figure 5.5. Baseband Block Diagram
The EB-G50 Baseband is built around a GSM chipset developed by Advanced Device. One chip (AD6525) carries out
signal processing with DSP and CPU, and the other chip (AD6521) provides the analogue interface.
The highly integrated nature of the chips means that each contains a large number of functions.
– 5–6 –
5.2.2. Digital Baseband Processor
GSM processor ADI AD6525
Package 160 -Ball LFBGA
Feature
Complete single chip GSM Programmable Digital Baseband Processor divided into three main
subsystems:
1.Control processor subsystem including
32-bit MCU ARM7TDMI control processor
39 MHz operation at 1.8V
1Mb on-chip System SRAM Memory
2. DSP subsystem including
16-bit Fixed-out DSP Processor
78 MIPS at 1.8V
Data and Program SRAM
Program Instruction Cache
Full rate, Enhanced full rate and Half Rate Speech Encoding / Decoding
Capable of Supporting PDC,AMR Speech Algorithms
3. Peripheral Subsystem including
Shared Peripheral Bus and Interface Peripherals
Figure 5.6. AD6525 Functional Block Diagram
– 5–7 –
5.2.3. Keypad
The Keypad has a 4 x 5 matrix, allowing 18 keys to be scanned. When a key being pressed, a
keypad interrupt is generated. To find which key has been pressed, the software scans each
column in turn and reads which row is active. Because of key bounce, the key press is confirmed
twice at approximately 40-60 ms intervals.
KEYCOL_0
KEYCOL_1
KEYCOL_2
KEYCOL_3
KEYCOL_4
SW 701
1
SW 702
2
1
SW 703
2
1
SW 704
2
1
SW 705
2
1
2
KEY [*]
KEY [7]
KEY [4]
KEY [1]
KEY_[UP]
SW 706
SW 707
SW 708
SW 709
SW 710
KEYROW_0
1
2
1
2
1
2
1
2
1
2
KEY [0]
KEY [8]
KEY [5]
KEY [2]
KEY_[DOWN]
SW 711
SW 712
SW 713
SW 714
SW 715
KEYROW_1
1
2
1
2
KEY [#]
KEY [9]
SW 716
SW 717
1
2
KEY [6]
1
2
KEY [3]
1
2
SOFT KEY_LEFT
KEYROW_2
1
2
SOFT KEY_RIGHT
1
2
KEY [SEND]
KEYROW_3
SW 718
1
2
POWER_KEY
POWERKEY&END
Figure 5.7. Keypad Connections
As the End Key doubles for the ON / OFF key, it is allocated an entire row of the keyboard scan.
Keyboard scanning is controlled by software.
5.2.4. Subscriber Identity Module (SIM)
The SIM interface is designed to support 3 V SIM card. And work voltage is supplied by ADP3522 "VSIM" (2.85 V).
0x00
0x02
0x04
0x06
0x0A
0x08
0x0C
SMSMR
SMBRR
SMSCR
SMTDR
SMRDR
SMSSR
SMSCMR
SIM Character Mode Register
SIM Bit Rate Register
SIM Control Register
SIM Data Transmit Register
SIM Data Receive Register
SIM Status register
SIM Smart Card Mode Register
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
– 5–8 –
5.2.5. CPU Memory
To reduce component space, the phone uses a BGA package with Dual operation Flash memory and SRAM MCP.
The following memory configuration is used:
64Mbits
Flash memory
organized as 4M * 16bits or 8M * 8bits
32Mbits
Pseudo RAM
organized as 2M * 16 bits
5.2.6. LCD
The LCD module consists of a LCD glass, white LED and driver chip connection to the Main PCB via a flexible PCB
strip. A 96 x 128 pixels graphical display is used which can display up to 21 characters x 5 rows - plus two rows of icons.
It can accommodate Chinese and large character sets.
Figure 5.8. LCD Dimensions
The LCD driver is controlled by setting the command register through the AD6525 u-wire interface and an I/O
line that distinguishes between command or data. To send data or a command to the display driver, the
nDISPLAYCS line is used for chip select. LCD_CTL is set high to send data and set low to send commands.
5.2.7. Real Tim Clock (RTC)
Clock functions are provided by a Real Time Clock built into AD6525. The module is synchronized by a 32.768 kHz
crystal and has a backup power source provided by a capacitor. AD6525 has a clock auto compensation function to take
into account any inaccuracies of the crystal. This is able to calibrate out crystal tolerance / drift by writing to the
compensation registers. This functionality allows the application software to implement standard, calendar, or organizer
functions such as:
Time and date display
Programmable alarm
Programmable mobile activation
The RTC interrupt is routed through the IRQ-controller to the MCU or the DSP, as defined by
software in interrupt configuration registers.
– 5–9 –
5.3. Audio System
MIC
VINNOR P/N
Receiver
VOUTNOR P/N
VINAUX P/N
Phone
Jack
Audio
AMP
VOUTAUX P/N
ADC/DAC
VoiceBand
&
BaseBand
Codec.
(AD6521)
A,V,B
serial Port
GSM Processor
(AD6525)
Buzzer(L_SPK Mode)
HPOUT
Meledy IC
MA1
Speaker
GPIO5
Control /Data
Interface
LDO 3.0V
Figure 5.9. Audio system block diagram
AD6521 is a Voiceband Baseband Codec (VBC) that combines, onto a single chip, all A/D and D/A converters that are
necessary to build a complete GSM, DCS1800, and PCS1900 mobile radio. It has two differential output port, two
differential input ports, and a buzzer output. Voiceband normal output is used in normal receiver mode.
Voiceband auxiliary output is used in earpiece receiver mode. Buzzer output signal via a meledy IC is used in loud-speak
mode. About input, voiceband normal input is used to microphone and the auxiliary input is design for earpiece microphone.
5.3.1. Voiceband Baseband Codec
Chipset ADI AD6521
Package 64-Ball LFBGA
Feature
■ Complete Analog/Digital Interface for Voiceband Input/Output-Signals; Baseband Input/Output-Signals;
Auxiliary/Control-Signals
■ Baseband Codec
Supports Multi-slot Operation
Differential I and Q Inputs/Outputs
On-Chip GMSK Modulator for GSM
Two 10-Bit D/A Converters
10-Bit RAMP D/A Converter
On-Chip RAMP-RAM
Two High Resolution A/D Converters
On-Chip FIR-Filter
■ Voiceband Codec
Complete Linear Coded Codec
Two Channel 16-Bit A/D Converter with Filter
Complete Microphone Interface
Two Channel 16-Bit D/A Converter with Filter
Complete Speaker Drive Capability
Programmable Gain on Input and Output
Multi-Standard Sample Rate Conversion
■ Auxiliary Section
13-Bit AFC D/A Converter
10-Bit Current DAC
Six Channel 10-Bit A/D-Converter
– 5–10 –
■
■
■
■
■
■
■
Individual Power Management Features
Baseband, Voiceband and Auxiliary Serial Ports
JTAG Interface
Optimized Low-Power Converter Design
Low 1.6V Digital Supply Operation
Variable Digital Interface Supply
Low 2.4V Analog Supply Operation
Figure 5.10. AD6521 Functional Block Diagram
5.3.2. Microphone
The microphone is a noise canceling type to provide improved speech pick-up, noise immunity
and reduced echo. The GSM standard requires that when in handheld mode, the transmitter audio
frequency response must fit within the mask shown below:
Figure 5.11. Handheld GSM Transmit Audio Frequency Response Mask
– 5–11 –
5.3.3. Receiver
The GSM Standard requires that the receiver audio frequency response must fit within the mask shown below.
Figure 5.12. Handheld GSM Receive Audio Frequency Response
The phone is designed to meet requirements with a Type 1 artificial ear.
Volume Level
1
2
3
4
PGA
+1 db
-2 db
-5 db
-5 db
Volume
0 db
0 db
0 db
-6 db
Total Gain
+3 db
-0 db
-3 db
-9 db
5.3.4. Loud Speaker
A second speaker is mounted in the rear case for DTHF operation.
Ring tones and melodies are played via the loud speaker. The volume level of ring tones is defined
by the 6-bit PWM register setting in AD6521, and melody tone volume defined by the
MASOUND_DEVICECONTROL register setting in the YMU762.
Timer 1 in AD6521 is used to time the period between switching the ringing on and off to make the
tone. For complex ringing tones, the buzzer volume can be altered after each time-out of Timer 1.
5.4. Timers
There is a watchdog timer and three 16 bit general-purpose timers which can be used either as
auto reload or one-shot timers to provide interrupts to the ARM CPU. A pre-scaler and 16-bit
register defines the timer clock duration. The watchdog timer receives a 217 Hz clock signal from
clock module. The time-out is fixed at 1024 clock ticks, which gives a time-out of approximately
4.72s. The general-purpose timers can receive different clock sources. The clock sources can be
System clock, MicroSM Clock, MicroSM timetick, 32KHz oscillator.
$8014:0000 Watchdog_R
$8014:0002 Watchdog_CR
$8014:0004 Watchdog_INT
$8020:0080 TimerStatus
$8020:0082 Reserved
$8020:0084 EndCountA
$8020:0086 TimerAControl
$8020:0088 EndCountB
$8020:008A TimerBControl
$8020:008C EndCountC
$8020:008E TimerCControl
Watchdog register,
Watchdog control register
Watchdog interrupt register
– 5–12 –
0 bit
1 bit
1 bit
6 bits
0 bit
16 bits
12 bits
16 bits
12 bits
16 bits
12 bits
Write only, reserved
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Wr
5.5. Power Management Subsystem
In base-band power management, ADI ADP3522 is designed for all base-band main power supply.
It provides six regulator outputs for VCORE (1.8V), VMEM (2.8V), VANA (2.55V), VRTC (1.95V), VCTCXO (2.75V),
SIMVCC (2.85V). VCORE and VMEM provide all digital power and VANA provides all analog power. VRTC is used to charge
Li-Mn coin cell for real time clock, and VCTCXO is the power source of 13MHz clock buffer. Besides, ADP3522 is also combined
charge pump and hardware reset. The following is the detailed description:
VMEM
LCD
Memory
Power on detection
and latching
VBAT
NReset
VCORE
ADP3522
13 MHz
Battery
VANA
VMEM
RTC
Circuit
VRTC
Charging
Circuit
SIMVCC
SIM
Circuit
AD6525
VCORE
VMEM
VCORE
VANA
Figure 5.13. Power Management Subsystem Block Diagram
– 5–13 –
AD6521
5.5.1. Power System Ship
Chipset
ADI ADP3522
Package
32-pin LFCSP5x5
FEATURES
■ Handles all GSM Baseband Power Management
■ Six LDOs Optimized for Specific GSM Subsystems
■ Li-Ion Battery Charge Function
■ Optimized for the AD20msp430 Baseband Chipset
■ Reduced Package Size: 5x5 mm LFCSP-32
ADP3522 is specified over the temperature range of –20 °C to +85 °C.
Figure 5.14. ADP3522 Functional Block Diagram
5.5.2. Power Source
The battery comprises a single Lithium-Ion (Li-Ion) cell with a nominal voltage of 3.7 V and 720-mAh capacity.
This type of battery has an advantage in weight and size over Nickel Metal Hydride (NiMH) cells.
– 5–14 –
5.5.3. Power On / Off Control
The ADP3522 handles all issues regarding the powering ON and OFF of the handset. It is possible to turn on the ADP3522
in three different ways:
8 Pulling the PWRONKEY Low
8 Pulling PWRONIN high
8 CHRIN exceeds CHRDET threshold
Pulling the PWRONKEY low is the normal way of turning on the handset. This will turn on all the LDOs on, except the
SIM LDO, as long as the PWRONKEY is held low. When the VCORE LDO comes into regulation the RESET timer is started.
After timing out, the RESET pin goes high, allowing the baseband processor to start up. With the baseband processor
running, it can poll the ROWX pin of the ADP3522 to determine if the PWRONKEY has been depressed and pull PWRONIN
high. Once the PWRONIN is taken high, the PWRONKEY can be released. Note that by monitoring the ROWX pin, the
baseband processor can detect a second.
5.5.4. Voltage Regulation
Each power source is specified as follows.
Digital Core LDO (VCORE)
The digital core LDO supplies the baseband circuitry in the handset (baseband processor and baseband converter).
The LDO has been optimized for very low quiescent current at light loads as this LDO is on whenever the handset is
switched on.
Memory LDO (VMEM)
The memory LDO supplies the system memory as well as the subsystems of the baseband processor including memory IO,
display, and melody interfaces. It is capable of delivering up to 150 mA of current and is available for either 1.8 V or 3 V
based systems. The LDO has also been optimized for low quiescent current and will power up at the same time as the core
LDO.
Analog LDO (VAN)
This LDO has the same features as the core LDO. It has furthermore been optimized for good low frequency ripple rejection
for use with the baseband converter sections in order to reject the ripple coming from the RF power amplifier.
VAN is rated to 180 mA, which is sufficient to supply the analog section of the baseband converter such as the AD6521,
as well as the microphone and speaker.
TCXO LDO (VTCXO)
The TCXO LDO is intended as a supply for a temperature compensated crystal oscillator, which needs its own ultra-low noise
supply. VTCXO is rated for 20 mA of output current and is turned on along with the analog LDO when TCXOEN is asserted.
RTC LDO (VRTC)
The RTC LDO is capable of charging rechargeable Lithium or capacitor-type backup coin cells to run the real-time clock
module. The RTC LDO supplies current both for charging the coin cell and for the RTC module. In addition it features a very
low quiescent current since this LDO is running all the time, even when the handset is switched off. It also has reverse current
protection with low leakage, which is needed when the main battery is removed and the coin cell supplies the RTC module.
SIM LDO (VSIM)
The SIM LDO generates the voltage needed for 1.8 V or 3 V SIMs. It is rated for 20 mA of supply current and can be controlled
completely independently of the other LDOs.
Applying a low to SIMEN shuts down the SIM LDO. A discharge circuit is active when SIMEN is low. This pulls the SIM LDO's
output down when the LDO is disabled. SIMVSEL allows the SIM LDO to be programmed for either 1.8 V or 2.8V. Asserting a
high on SIMVSEL sets the output for 2.8 V. SIMEN and SIMVSEL allow the baseband processor to properly sequence the
SIM supply when determining which type of SIM module is present.
– 5–15 –
5.6. Battery Charging and Monitoring
5.6.1. Charging Current
The status of the LCD battery icon is determined by the value of ADC0 returned from AD6521, as
indicated in the table:
3 bar
2 bar
1 bar
Low Voltage Alarm
3.65 V <
3.54 V <
3.3 V <
Battery Pack
Li-lon
< 3.95 V
< 3.65 V
< 3.54 V
< 3.3 V
The phone will power down two minutes after generating a Low battery Alarm.
Battery charging is controlled by the CPU within the phone. If external power is detected and the temperature is within
specified limits, the charger starts the rapid charge algorithm.
When the battery is fitted, the charging algorithm is determined by constant voltage and constant current control with time,
temperature and voltage safeguards. A current limit no greater than the maximum charge current for any battery option
must be provided by the external power source.
5.6.2. Deeply Discharged Batteries
In the case of deeply discharged batteries, there may not be enough power in the battery to initiate charging. In this case,
the charging circuit automatically starts to trickle charge the battery until there is enough power to switch on the phone.
– 5–16 –
6. DISASSEMBLY / REASSEMBLY INSTRUCTIONS
6.1. General
This section provides disassembly and reassembly procedures for the main components of the telephone.
These assemblies MUST be performed by qualified service personnel at an authorized service center.
The following Warnings and Cautions MUST be observed during all disassembly / reassembly operations:
WARNING
The equipment described in this manual contains polarized capacitors utilizing liquid electrolyte. These devices are entirely
safe provided that neither a short-circuit nor a reverse polarity connection is made across the capacitor terminals.
FAILURE TO OBSERVE THIS WARNING COULD RESULT IN DAMAGE TO THE EQUIPMENT OR, AT WORST,
POSSIBLE INJURY TO PERSONNEL RESULTING FROM ELECTRIC SHOCK OR THE AFFECTED CAPACITOR
EXPLODING. EXTREME CARE MUST BE EXERCISED AT ALL TIMES WHEN HANDLING THESE DEVICES.
Caution
The equipment described in this manual contains electrostatic devices (ESDs). Damage can occur to these devices if the
handling procedures described are not adhered to.
6.1.1. Call Bar
A working area where ESDs may be handled safely without undue risk of damage from electrostatic discharge must be
available. The area must be equipped as follows.
Working Surfaces
All working surfaces must have a dissipative bench mat, safe for use with live equipment, connected via 1M2 resistor
(usually built into the lead) to a common ground point.
Wrist Strap
A QUICK RELEASE SKIN CONTACT DEVICE WITH A FLEXIBLE CORD, WHICH HAS AN INTEGRAL SAFETY
RESISTOR OF BETWEEN 5K2 AND 1M2, SHALL BE USED.
Containers
All containers and storage must be of the conductive type.
– 6–1 –
6.2. Disassembly
1. Take out the Antenna Knob by tweezers.
2. Push the Battery Knob up to remove the battery and unscrew 2 screws on the Base Case.
3. Carefully prise apart the Upper Case and Bottom Case, creating a gap around the DC Jack.
Insert the separation tool into the gap ceated, and gently slide the tool in the direction as shown,
ensuring that the moduled hocks separate all the way.
– 6–2 –
4. Take out the Upper Case and unscrew 1 screw located on PCB-A.
5. Carefully lift PCB-A from right side and pull out the Vibrator Cable to completely separate from
the PCB- and the base Unit.
6. Take out the Receiver Rubber.
– 6–3 –
7. Remove the Microphone.
8. Unsolder the hook of Shield-Key (on top of the RTC) and detach from the PCB-A.
9. Gently separate the glue in both sides and remove the Shield-Key.
– 6–4 –
10. Gently prise two ears of the LCD Module to separate it from the PCB-A..
11. Carefully lift up the connector cover to vertical to take out the LCD Module.
12. Remove the Key Set from the Upper Case.
– 6–5 –
13. Remove the MIC Holder from the Base Case.
14. Lift the Vibrator and Speaker from the Base Case by inserting small blunt object underneath
them.
15. Narrow the hooks of the Antenna Ass'y, push upward and take it out.
– 6–6 –
16. Carefully narrow the Battery Knob by pressing both hooks from internal side of the Base Case
push the hooks downward to slide out.
17. Pull down the Battery Knob from outside to completely remove.
18. Take out the Battery Knob Spring.
– 6–7 –
6.3. Reassembly
1. Put the Battery Knob Spring back.
2. Locate the Battery Knob in the middle and push upward to the top and release. make sure the
Knob keep normal flexibility.
3. Push the Antenna Ass'y downward until the hooks are fixed probably.
– 6–8 –
4. Utilize the bulge to put the Speaker and Vibrator back into the fillister.
5. Fix the MIC Holder in the Base Case as shown.
6. Put the Shield_Top and Shield-SIM-Holder back. If the shields are out of shape, replace a
new one.
– 6–9 –
7. Insert the MIC into the PCB-A by aligning pins in down sides.
8. Carefully insert the LCD Cable, close the connector cover and attach the LCD Module.
9. Cover Shield-Key and solder the hook (on top of the RTC) to ensure complete performance.
– 6–10 –
10. Cover the Receiver with the Receiver Rubber.
11. Insert the Vibrator Cable into connector and organize the Cable to avoid stuck.
12. Put the PCB-A into the Base Case from the Phone Jack side.
Make sure the PCB-A located probably.
– 6–11 –
13. Tighten the screw on the PCB-A.
14. Assemble the Upper Case by combining from top.
15. Carefully press along both sides to make sure the casing fixed probably.
Check the side caps are within specifications.
– 6–12 –
16. Tighten 2 screws on the Case and put the Antenna Rubber in the hole.
– 6–13 –
7. REPAIR PROCEDURES
7.1. Introduction
This section provides information on testing the telephone. Thelayout is as follows:
Section 7.2. :
Section 7.3. :
Section 7.4. :
Lead Free (PbF) solder: Identification and repair of PCBs using PbF solder.
External testing: describes equipment requirements and general set up procedure.
Complete Unit Test Setup: Describes how the items of test equipment are used together and general set
up procedure.
Adjustment Procedure are described in Section 8.
7.2. Lead Free (PbF) solder
CAUTION
The Printed Circuit Board (PCB) used in this telephone has been manufactured using Lead Free solder.
(SPARKLE ECO SOLDE : Part No. ESC F3 M705 0.3)
Lead Free solder has a higher melting point than Lead solder - typically 30 - 40 °C higher. Always use a high temperature soldering iron
When using a soldering iron with temperature control, it should be set to 370 ± 10 °C (700 ± 20 °F).
When using lead solder, all PbF solder must be removed from the solder area. Where this is not possible, heat the PbF solder until it
melts before applying lead solder.
Avoid over heating PbF solder as it has a tendency to splash at temperatures above 600 °C (1100 °F).
7.3. External Testing
7.3.1. General Information
The handset can be connected to a compatible personal computer for electronic adjustment and fault diagnosis. This section
provides a description of the equipment required to perform those tasks.
Prior to testing and adjustment, the unit should first be disassembled, as detailed in Section 6, and then the PCB connected to
the PCB Repair Jig. Fault tracing can be performed on the PCB using suitable test equipment, such as spectrum analysers
and oscilloscope.
The unit must be tested and calibrated for all frequency bands (900 MHz and 1900 MHz).
Personal Computer (PC)
The PC (IBM compatible) is used as a Unit Under Test controller.
Power Supply
Provides 3.8 V DC supply to RF Adaptor and PCB Repair Jig.
– 7–1 –
PCB Repair Jig (Part No. 3WZ001102AAA)
The PCB Repair Jig provides the necessary connections between the PCB Assembly and external test equipment. It is
required for RF calibration.
Figure 7.1. : PCB Repair Jig
A cable with SMA female connector is provided to make the RF connection. An SMA to N-Type male adaptor will be required
to connect the Repair Jig to the service equipment. Cable loses for the RF connection are 0.5 dBm (GSM 900) and 0.8 dBm
(GSM 1800).
A replacement RF Probe for the Repair Jig is available as a spares item.
– 7–2 –
DL Cable (Part No. DD0VE2TH004)
DL Cable is used for software download and TX Power/RX RSSI calibration with dummy battery.
Figure 7.3. : DL Cable
RF Cable (Part No. 3WZ001103AAA)
The RF cable provides the necessary connections between the PCB Repair Jig/RF Adapter and external test equipment.
Figure 7.4. : RF Cable
Case Separation Tool (Part No. JT00059)
The case Separation Tool is used to facilitate separation of the front cover and case.
Figure 7.5. : Case Separation Tool
– 7–3 –
Dummy Battery (Part No. 3WZ001104AAA)
Dummiy battery is used for software download and Battery calibration.
Figure 7.6. : Dummy Battery
GSM Tester
This unit acts as a base station providing all the necessary GSM signalling requirements and also provides GSM
signal measuring facilities.
Calibration Software
This is the test software for the telephone unit and should be installed onto the personal computer to be used for testing.
T5 Screwdriver
This screwdriver is required to remove the case screws from the phone.
– 7–4 –
7.4. Test Equipment Setup
7.4.1. Equipment Required
PCB Repair Jig
GSM
Tester
PC
RF Cable
DL Cable
Dummy
Battery
3.8 V DC
Power
Supply
PCB TEST SETUP
Handset
RF Cable
GSM
Tester
PC
DL Cable
Dummy
Battery
3.8 V DC
Power
Supply
COMPLETE UNIT TEST SETUP
Figure 7.7. : Test Connection Diagram
IMPORTANT NOTE
To allow accurate measurement of the complete unit the test equipment must be connected as shown,
For testing the handheld unit the following equipment is required:
1.
2.
3.
4.
5.
6.
7.
PCB Repair Jig
DL Cable
RF Cable
12 V power supply
Personal computer with RS232 interface and running Microsoft Windows® 95, 98, NT, XP or 2000
GSM test station
G50 Service software
The G50 Service software should be installed onto the main drive of the personal computer.
The RF cable is connected to the GSM test station via suitable adaptor. The 3.8 V supply is connected
to the RF Adptor and PCB Repair Jig.
NOTE: A suitable test SIM card compatible with the GSM test station will be required.
– 7–5 –
8. SOFTWARE DOWNLOAD &
ADJUSTMENT PROCEDURE
8.1. Service Software Upgrade
Equipment setting for single downloading:
PC
Handset
RS232
D/L Cable
1. Install the download tool on PC.
2. Keep the handset off. make sure the correct target file (*.mbf) is ready.
(Please make sure the capacity of battery is enough during downloading.)
– 8–1 –
3. Execute main program
(In the first time or target file is removed, it will show "File not found".)
1
2
4
3
The program will detect how many ports are available on PC.
3-1 Select download function.
3-2 Click the wheel icon and select the target file.
3-3 Long press on the power key and follow the indication on screen.
The progress status will be shown on screen.
3-4 If any fail happens, click that single failed handset icon and press "Reset".
– 8–2 –
8.2. MMI Test
In EB-G50, the repair technicians can dial *#369# on handset under normal operating condition to check
or adjust the below functions. Please notice the items 4,5,7 are for production and for special purpose,
don't change the default value arbitrarily or may cause mobile malfunction.
1. Contrast: Up& Down to adjust; Select & Back to exit.
2. Baseband test: Up & Down to chose item; Select to enter.
■ Back Light: test if the backlight shows; OK to exit.
■ Buzzer: test if the ring tone gives sound, OK to exit.
■ Vibrator: test if the vibrator works, OK to exit.
■ Keypads: press each key to eliminate the indicators on screen; long press OK to exit.
■ RTC status: show if the RTC OK; OK to exit.
■ Mic. Speaker Test: blow to microphone and listen the sound from receiver; OK to exit.
3. Software Version: Check the current software version
■ Software Version
■ Mapping Version
■ LP Version
4. Auto-answer: Valid setup when insert test SIM
5. DTMF-On: Determine if DTMF function valid during calling.
6. LCD Test:
■ Black: click any key to exit.
■ White: click any key to exit.
■ RGB: click any key to exit.
7. Comport:
■ AT-DATA: set phone jack for special D/L port, ex: IMEI burning.
■ GENIE
■ Off: set phone jack for normal earphone usage.
– 8–3 –
8.3. ADJUSTMENT PROCEDURE
8.3.1. Equipment Setting for TX/RX adjustment
1. Connect all equipments as above.
2. Please set the cable loss within the GSM tester before proceeding to any tests. It's
recommended that each band (GSM 900 /DCS 1800/PCS 1900) tested separately.
3. Power on the handset before executing the main program.
4. Change the handset comport setting: *#369#->Com port->GENIE
Notice:
1. Please make sure the RF probe contacts properly during the test process.
2. Remember to set the handset comport setting back to "Off" after adjustment, or it will cause
malfunction to earphone.
8.3.2. Main Subjects
<A> TX Power
8 TX Power Scaling Factors
8 TX Freq Compensation
<B> RX RSSI (Received Signal Strength Indication)
8 Accurate Gain Control
8 RX Freq Compensation
<C> Battery Calibration
Band
TX/Fu(n)
RX/Fl(n)
ARFCN
0 n 124
Fu(n)=890+0.2*n
Fu(n)=890+0.2(n-1024)
Fl(n)=Fu(n)+45
DCS1800
Fu(n)=1710.2+0.2(n-512)
Fl(n)=Fu(n)+95
512 n 885, Middle: 698
PCS1900
Fu(n)=1850.2+0.2(n-512)
Fl(n)=Fu(n)+80
512 n 810, Middle: 661
E-GSM900
975 n 1023, Middle: 37
ARFCN: Absolute Radio Frequency Channel Numbers
– 8–4 –
8.3.3. Test Operation Procedure
Execute the main program "PAC CalTool V3.0.exe"
■ Enter Test
1. Select the related "PORT", "MODEL".
2. Click [ENTER TEST MODE].
3. If successful, the information dialog will pop up witin 3 sec and click [OK].
– 8–5 –
■ TX Test
Power Control Level
GSM 900
Power
Transmitter
Control Level Output Power
dbm
0-2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19-31
39
37
35
33
31
29
27
25
23
21
19
17
15
13
11
9
7
5
Tolerances
Normal Extreme
2
3
3
3
3
3
3
3
3
3
3
3
3
3
5
5
5
5
2.5
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
PCS 1900
DCS 1800
Power
Transmitter
Control Level Output Power
dbm
Tolerances
Power
Transmitter
Control Level Output Power
Normal Extreme
dbm
Tolerances
Normal
Extreme
29
36
2
2.5
22-29
Reserved
30
34
3
4
30
33
2
2.5
31
32
3
4
31
32
2
2.5
0
30
3
4
0
30
3
4
1
28
3
4
1
28
3
4
2
26
3
4
2
26
3
4
3
24
3
4
3
24
3
4
4
22
3
4
4
22
3
4
5
20
3
4
5
20
3
4
6
18
3
4
6
18
3
4
7
16
3
4
7
16
3
4
8
14
3
4
8
14
3
4
9
12
4
5
9
12
4
5
10
10
4
5
10
10
4
5
11
8
4
5
11
8
4
5
12
6
4
5
12
6
4
5
13
4
4
5
13
4
4
5
14
2
5
6
14
2
5
6
15-28
0
5
6
5
6
15
0
16-21
Reserved
– 8–6 –
Reserved Reserved
Reserved Reserved
There are two parts in this test item.
(1) TX POWER SCALING FACTOR
1. Click [Read] to read the values inside the handset as reference.
2. Select "BANDMODE", EGSM_DCS for 900/1800, EGSM_PCS for 1900
3. Enter the ARFCN of each middle band-> click [APPLY] (ex: EGSM–37) and set tester in the same
channel.
4. Enter the estimate value in SCALING FACTOR -> click [APPLY] and read the TX output power value
on the tester. Repeat until the TX power is within the allowed range.
5. Repeat step 2-4 for the other bands which are optional.
6. Click [WRITE] when the chosen bands are all tested to adjust the handset.
3
4
2
1
– 8–7 –
6
(2) TX FREQ COMPENSATION
1. Select "BANDMODE", EGSM_DCS for 900/1800, EGSM_PCS for 1900
2. Enter the first ARFCN listed in CH column -> click [APPLY] and set tester in the same channel.
3. Enter the estimate value in SCALING FACTOR -> click [APPLY] and read the TX output power value
on the tester. Repeat until the TX power is within the allowed range.
4. Enter the ideal scaling factor in the corresponding cell of SF column.
5. Repeat step 2-4 until ALL 9 channels are down.
6. Click [WRITE] to adjust the handset in the end.
1
2
3
6
4
– 8–8 –
■ RX Test
There two parts in this test item.
(1) RX POWER SCALING FACTOR
Set tester as (a) Test Function: CW (b) RF Gen Power: -60dbm (c) MS TX Level: 5
1. Click [Read] to read the values inside the handset as reference.
2. Select "BANDMODE", EGSM_DCS for 900/1800, EGSM_PCS for 1900.
3. Enter the ARFCN of each middle band and plus 0.0677 MHz to tester's RF Gen Frequensy in the
related.
4. Click [SEND], the RSSI and OFFSET will be counted automatically and shown on.
5. Click [OFFSET] related to the test band.
6. Repeat step 2-4 for the other bands which are optional.
7. Click [WRITE] when the chosen bands are all tested to adjust the handset.
3
5
7
2
1
4
– 8–9 –
(2) RX FREQ COMPENSATION
Set tester as (a) Test Function: CW (b) RF Gen Power: -60dbm (c) MS TX Level: 5
1. Select "BANDMODE", EGSM_DCS for 900/1800, EGSM_PCS for 1900
2. Enter the first ARFCN in the CH column and plus 0.0677MHz to tester's RF Gen Freq in the related.
3. Click [SEND],
4. Enter the shown RSSI value in the corresponding cell of RSSI column.
5. Repeat step 2-4 until ALL 9 channels are down.
6. Click [WRITE] to adjust the handset in the end.
2
1
3
6
4
– 8–10 –
8.3.4. Battery
Equipment setting for battery adjustment
Notice:
1.Change the handset comport setting: *#369#->Com port->GENIE before process.
2.Remember to set the handset comport setting back to ÅgOffÅh after adjustment, or it will cause
malfunction to earphone.
Operation Process
1. Click [Read] to read the values inside the handset as reference.
2. Set power supply to 4.2V DC and click [ADC] and enter the value shown into the 4.2 V cell.
3. Set power supply to 3.2V DC and click [ADC] and enter the value shown into the 3.2 V cell.
4. Click [WRITE] to adjust the handset.
1
4
2
3
– 8–11 –
9. REPLACEMENT PARTS LIST
9.1. Case and Cover Parts
M8
Ref. No
Description
Sliver
Red
Blue
Upper Case + Panal (BPMF)
1MIZZZZPAG8
1MIZZZZPAH6
1MIZZZZPAI4
Upper Case + Panel (Standard)
1MIZZZZPAJ1
1MIZZZZPAK9
1MIZZZZPAL7
Upper Case + Panel (Stroke)
1MIZZZZPA19
1MIZZZZPA27
1MIZZZZPA35
Upper Case + Panel (Thai)
1MIZZZZPAM5
1MIZZZZPAN3
1MIZZZZPAP1
T1
KEY JEWEL + P+R KEY SET
34VE2KBPA01
34VE2KBPA10
34VE2KBPA28
B
BASE CASE
EAVE2003011
EAVE2003020
EAVE2003038
B1
ANTENNA ASS'Y
DQ600233109
DQ60023105
DQ600253100
B5
CAR KIT RUBBER
GAVE2001019
GAVE2001027
GAVE2001035
B7
BATTERY KNOB
EBVE2001010
EBVE2001028
EBVE2001036
C
BATTERY ASS'Y (EU)
AHL03707211
AHL03707246
AHL03707220
BATTERY ASS'Y (US)
AHL03707289
AHL03707271
AHL03707297
BATTERY ASS'Y (CN)
AHL03707238
AHL03707262
AHL03707254
Description
Part NO
T
Ref. No
Description
Part NO
Ref.
No
M
PCBA (INTL)
10MBZZZPA25
M7
MIC
DNWM63PR011
PCBA (CN)
21VE2MB0009
M8
RECEIVER
DND501D2004
M1/B8 SCREW
MS16040IKQ8
B2
SPEAKER
DNDSH486002
M2
SHIELD-KEY
FBVE2001010
B3
VIBRATOR
AY010312301
M3
LCD MODULE
AA001209001
B4
MIC HOLDER
GBVE22002016
M4
RECEIVER RUBBER
GBVE2001010
B6
BATT KNOB SPRING
FDE2001011
M5
SHIELD-TOP
FBCE2005019
KEY PAD ASS'Y
35VE2KAPA07
M6
SHIELD-SIM-HOLDER
FBVE1002012
– 9–1 –
9.2. Main PCB Assembly
Cct Ref
Part No.
AN1161
B1221
B1222
B1241
BAT101
DFHD01MS101
CX1HB102001
CX1HB102001
CX1HB102001
CC9700KTZ08
C201
C214
C218
C301
C304
Part Name & Description
Grid
Cct Ref
Part No.
CONN SMD SPRING HD 1P 1R MS(P2.3,H7.3)
EMI FILTER CHIP BLM11HB102SDPT
EMI FILTER CHIP BLM11HB102SDPT
EMI FILTER CHIP BLM11HB102SDPT
RTC
C1116
C1141
C1143
C1145
C1154
CH03306JBD7
CH03906JBD9
CH03306JBD7
CH01206JBD8
CH01006JBD1
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
33pF 50V
39pF 50V
33pF 50V
12pF 50V
10pF 50V
CH52201M993
CH31003KB11
CH52201M993
CH54701MA99
CH54701MA99
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
2.2uF 6.3V
0.01uF 16V
2.2uF 6.3V
4.7uF 6.3V
4.7uF 6.3V
C1155
C1156
C1171
C1172
C1173
CH03306JBD7
CH01206JBD8
CH03306JBD7
CH01006JBD1
CH01006JBD1
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
33pF 50V
12pF 50V
33pF 50V
10pF 50V
10pF 50V
C305
C306
C307
C308
C309
CH54701MA99
CH54701MA99
CH52202MA91
CH51001K991
CH31003KB11
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
4.7uF 6.3V
4.7uF 6.3V
2.2uF 10V
1uF 6.3V
0.01uF 16V
C1174
C1175
C1176
C1177
C1178
CH51001K991
CH51001K991
CH51001K991
CH31003KB11
CH61001ZA31
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
1uF 6.3V
1uF 6.3V
1uF 6.3V
0.01uF 16V
10uF 6.3V
C310
C312
C317
C318
C319
CH52204ZE42
CH31003KB11
CH31003KB11
CH06806JB01
CH31003KB11
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
2.2uF 25V
0.01uF 16V
0.01uF 16V
68pF 50V
0.01uF 16V
C1180
C1181
C1182
C1184
C1202
CH01506JB06
CH06806JB01
CH11504JBD0
CH03306JBD7
CH03906JBD9
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
15pF 50V
68pF 50V
150pF 25V
33pF 50V
39pF 50V
C324
C325
C404
C405
C515
CH01806JB07
CH03906JBD9
CH03306JBD7
CH02206JBD1
CH03306JBD7
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
18pF 50V
39pF 50V
33pF 50V
22pF 50V
33pF 50V
C1203
C1204
C1205
C1211
C1214
CH22206KB16
CH03906JBD9
CH11006JBD2
CH02206JBD1
CH14706KB18
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
2200pF 50V
39pF 50V
100pF 50V
22pF 50V
470pF 50V
C516
C517
C518
C523
C524
CH03306JBD7
CH31003KB11
CH12006KB17
CH03306JBD7
CH03306JBD7
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
33pF 50V
0.01uF 16V
200pF 50V
33pF 50V
33pF 50V
C1215
C1221
C1223
C1225
C1226
CH14706KB18
CH02206JBD1
CH02206JBD1
CH21006JB10
CH01006JBD1
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
470pF 50V
22pF 50V
22pF 50V
1000pF 50V
10pF 50V
C525
C526
C528
C601
C602
CH52201M993
CH54701MA99
CH31003KB11
CH31003KB11
CH61001ME96
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
2.2uF 6.3V
4.7uF 6.3V
0.01uF 16V
0.01uF 16V
10uF 6.3V
C1227
C1228
C1229
C1242
C1243
CH16806KB17
CD28203JT09
CH12206JB00
CH61001ZA31
CH02206JBD1
CERAMIC CAPACITOR
MYLAR CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
680pF 50V
8200pF 16V
220pF 50V
10uF 6.3V
22pF 50V
C607
C608
C610
C611
C615
CH03306JBD7
CH03306JBD7
CH03306JBD7
CH03306JBD7
CH03306JBD7
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
33pF 50V
33pF 50V
33pF 50V
33pF 50V
33pF 50V
C1245
C1247
C1248
C1249
C1250
CH02206JBD1
CH01006JBD1
CH03306JBD7
CH33302KB12
CH-2706TB06
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
22pF 50V
10pF 50V
33pF 50V
33nF 50V
2.7pF 50V
C616
C623
C624
C626
C628
CH61002MA41
CH11006JBD2
CH11006JBD2
CH61001ME96
CH61002MA41
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
10uF 10V
100pF 50V
100pF 50V
10uF 6.3V
10uF 10V
C1253
C1254
C1262
C1265
C1267
CH03306JBD7
CH01806JB07
CH01506JB06
CH01506JB06
CH01206JBD8
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
33pF 50V
18pF 50V
15pF 50V
15pF 50V
12pF 50V
C629
C630
C735
C736
C737
CH52201M993
CH52201M993
CH31003KB11
CH52201M993
CH61001ME96
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
2.2uF 6.3V
2.2uF 6.3V
0.01uF 16V
2.2uF 6.3V
10uF 6.3V
C1271
C1272
CON301
CON302
D713
CH+5006TB07
CH+5006TB07
DFHD03MS240
DFHS04FS080
BC1SS355Z05
CERAMIC CAPACITOR
CERAMIC CAPACITOR
BATTERY CONNECTOR
DC JACK
DIODE SMD 1SS355
0.5pF 50V
0.5pF 50V
C738
C739
C740
C754
C1102
CH51001K991
CH51001K991
CH51001K991
CH61002MA41
CH03306JBD7
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
1uF 6.3V
1uF 6.3V
1uF 6.3V
10uF 10V
33pF 50V
F302
J401
J601
J1161
M701
DK100WFU013
DG006000114
DFPJ06FR018
DFRF06FS022
DFHS02FS081
FUSE SMD 1A 32V
SIM CONNECTOR
PHONE JACK
CAR KIT CONNECTOR
VIBRATOR CONNECTOR
C1103
C1107
C1108
C1112
C1113
CH31003KB11
CH11006JBD2
CH31003KB11
CH31003KB11
CH03306JBD7
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
0.01uF 16V
100pF 50V
0.01uF 16V
0.01uF 16V
33pF 50V
– 9–2 –
Part Name & Description
Grid
Cct Ref
Part No.
Part Name & Description
Grid
Cct Ref
Part No.
Part Name & Description
L301
L1102
L1142
L1161
L1162
CV-2201KN16
CVB4703TN04
CH+5006TB07
CVA1503JN00
CVA1503JN00
INDUCTOR CHIP
INDUCTOR CHIP
CERAMIC CAPACITOR
INDUCTOR CHIP
INDUCTOR CHIP
2.2uH
4700pH
0.5pF 50V
0.015uH
0.015uH
R1203
R1204
R1205
R1206
R1207
CS12202FB06
CS13902JB06
CS15102FB01
CS05102JB01
CS01002JB06
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
220O 1/16W
390O 1/16W
510 1/16W
51O 1/16W
10O 1/16W
L1201
L1211
L1241
L1261
LS501
CV+1803JN00
CVA8201GN0
CVA2702JN04
CVB8203JN00
FDDG1003011
IND CHIP
IND CHIP
INDUCTOR CHIP
INDUCTOR CHIP
SPEAKER SPRING
0.18uH
0.082uH
0.027uH
8200pH
R1221
R1222
R1223
R1224
R1225
CS33902FB08
CS01002JB06
CS01002JB06
CS01002JB06
CS25602JB02
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
39K 1/16W
10O 1/16W
10O 1/16W
10O 1/16W
5.6K 1/16W
R102
R105
R106
R201
R206
CS61003J903
CS41002JB03
CS41002JB03
CJ410042N04
CS41002JB03
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
SPECIAL FIXED RESISTOR
FIXED RESISTOR
10M 1/10W
100K 1/16W
100K 1/16W
100K 1/16W
100K 1/16W
R1226
R1232
C1252
T301
U101
CS22002FB01
CS31002JB01
CS11802JB07
CY040205B01
AJ065250T07
FIXED RESISTOR
2K 1/16W
FIXED RESISTOR
10K 1/16W
FIXED RESISTOR
180O 1/16W
SURGE SUP VC040205X150 (5.6V,0402)
AD6525
R207
R208
R209
R210
R211
CJ410042N04
CS42002FB04
CU410000Z07
CS41002FB01
CS42002FB04
SPECIAL FIXED RESISTOR
FIXED RESISTOR
THERMISTOR
FIXED RESISTOR
FIXED RESISTOR
100K 1/16W
200K 1/16W
100K
100K 1/16W
200K 1/16W
U201
U301
U506
U302
U305
AJ065210T05
AJ035220U07
AL000762081
BCDAN222001
AL7SZU04019
AD6521
ADP3522
MA3 YMU762
DIODE DAN222 (80V,300MA) SWITCH
IC (5P) NC7SZU04P5X
R212
R213
R301
R302
R303
CU410000Z07
CS41002JB03
CS41002JB03
CS41002JB03
CS+3004FA04
THERMISTOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
100K
100K 1/16W
100K 1/16W
100K 1/16W
0.3O 1/8W
U306
U307
U308
U309
U311
BC55C9V1Z06
BAM06400Z03
BAMEMD20Z07
BAM34430004
BC0CRS03Z09
DIODE SMD BZM55C9V1-TR
TRANSFER MOSFET FDC640P
TRANSISTOR MOSFET EMD2 T2R
TRANSISTOR MOSFET SI3443DV
DIODE SMD CRS03
R307
R309
R310
R401
R403
CS51002JB05
CS31002JB01
CS31002JB01
CJ000084N25
CS31002JB01
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
SPECIAL FIXED RESISTOR
FIXED RESISTOR
1M 1/16W
10K 1/16W
10K 1/16W
0O 1/16W
10K 1/16W
U312
U505
U507
U601
U603
BC0CRS03Z09
AL001563019
CY000956001
AL002985065
ALSB3157000
DIODE SMD CRS03
IC (5P) SC1563ISK-3.0TR
SURGE SUP BZA956A
IC (5P) LP2985AIM5X-2.5
IC (6P) NC7SB3157P6X (SC70-6)
R404
R405
R508
R509
R514
CS11502FB04
CS41002JB03
CS32002JB04
CS34702JB05
CS31002JB01
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
150O 1/16W
100K 1/16W
20K 1/16W
47K 1/16W
10K 1/16W
U605
U703
U704
U1101
U1103
CY000956001
AL002985014
AL000600000
AL077314001
AL008315002
SURGE SUP BZA956A
IC (5P) LP2985AIM5X-3.0
IC (10P) SC600BIMSTR
CX77314
AD8315
R521
R602
R609
R610
R611
CS41002JB03
CS24702JB03
CS51002JB05
CS51002JB05
CS00002JB03
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
100K 1/16W
4.7K 1/16W
1M 1/16W
1M 1/16W
0O 1/16W
U1131
U1141
U1171
U1172
U1173
DP200007A01
AT0L090TZ17
BAPEMB30Z07
BAPEMB30Z07
AL009122011
COUPLER DUAL LDC15D190A0007A
HYBRID
TRANSISTER SMD PEMB3
TRANSISTER SMD PEMB3
IC ( 8P) MAS9122ASM3-T TRIPLE LDO (MSOP8)
R615
R626
R633
R637
R639
CS34702JB05
CS22402JB07
CS41002JB03
CS41002JB03
CS51002JB05
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
47K 1/16W
2.4K 1/16W
100K 1/16W
100K 1/16W
1M 1/16W
U1201
U1261
U1271
U1272
U1291
AL072063A05
CXT05R05001
CX007744008
CX007740002
BF626000004
CX74063
FILTER SAW SAFSE942MAL0T05R05 (2.5*2*1)
FILTER SAW B7744 (1842.5MHZ 2.5*2.0*0.8)
FILTER SAW RF B7740 (2.5*2.0*0.8MM)
OSCILLATER
R640
R709
R710
R1101
R1102
CS41002JB03
CS41002JB03
CS41002JB03
CS12202FB06
CT030R3N001
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
ATTENUATOR
100K 1/16W
100K 1/16W
100K 1/16W
200O 1/16W
X101
BG332768372
XTAL SMD 32.768KHZ
R1103
R1131
R1142
R1190
R1191
CT030R3N001
CS05102JB01
CS21002JB00
CS05112FB03
CS19092FB09
ATTENUATOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
51O 1/16W
1K 1/16W
51.1O 1/16W
909O 1/16W
R1192
R1193
R1198
R1199
R1202
CS05112FB03
CS35102JB06
CS21002JB00
CS21202JB07
CS15102FB01
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
51.1O 1/16W
51K 1/16W
1K 1/16W
1.2K 1/16W
510 1/16W
– 9–3 –
Grid
9.3. MMI (Keyboad) PCB Assembly
Cct Ref
Part No.
Part Name & Description
C7
C531
C532
C733
CH03306JBD7
CH03306JBD7
CH03306JBD7
CH41002KB93
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
33pF 50V
33pF 50V
33pF 50V
0.1uF 10V
C746
C747
C748
C749
C750
CH01806JB07
CH01806JB07
CH01806JB07
CH01806JB07
CH03306JBD7
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
18pF 50V
18pF 50V
18pF 50V
18pF 50V
33pF 50V
C751
C752
C753
D701
D702
CH03306JBD7
CH03306JBD7
CH01806JB07
BEBL0026Z00
BEBL0026Z00
CERAMIC CAPACITOR
CERAMIC CAPACITOR
CERAMIC CAPACITOR
LED
LED
33pF 50V
33pF 50V
18pF 50V
D703
D704
D709
D710
MIC601
BEBL0026Z00
BEBL0026Z00
BEBL0026Z00
BEBL0026Z00
DFHS02FR068
LED
LED
LED
LED
MIC CONNECTOR
R701
R704
R706
R707
R713
CS11002FB06
CS00824JA05
CS11002JB08
CS31002JB01
CS11002FB06
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
FIXED RESISTOR
R714
JP702
U701
U702
CJ120084N14
CS00002JB03
DFHS26FR233
BA022220004
SPECIAL FIXED RESISTOR
220O 1/8W
FIXED RESISTOR
0O 1/16W
LCD CONNECTOR
TRANSISTOR SMD FFB2222A 40V,500MA
Grid
Cct Ref
100O 1/8W
8.2O 1/8W
100O 1/16W
10K 1/16W
100O 1/8W
– 9–4 –
Part No.
Part Name & Description
Grid
Speaker
Phone
Jack
Receiver
MIC
R.F.
Block
Audio
HPOUT
VOUT AUX P
LDO 3.0V
PJ_FUNC_SEL
An alog
Switch
VINAUX P/N
TX/RX
VOUTNOR P/N
VINNOR P/N
VTCXO
Buffer
Keyboard
VANA
VCORE
A,V,B
serial Port
SIMVCC
SIM interface
32.768kHz
BBCLK
YMU_AVCC
Melody IC
PJ_FUNC_SEL
Control/Data
Interface
GPIO6
GPO22
GPIO12
– 10–1 –
GPIO13
VRTC
VMEM
VCC
GSM Processor
(AD6525)
OSC
CLKIN
Keypad Data Bus
Buzzer (L_SPK Mode)
ADC/DAC
VoiceBand
&
Base Band
Codec.
(AD6521)
SIM
Socke t
RTC
Crystal
RF Control Bus
Control Signal
RX IQ
TX IQ
13MHz_BB
10.1. Block Diagram of Base Band
10. BLOCK DIAGRAM
RTC
Battery
SIMVCC
VRTC
VTCXO
VANA
VMEM
VCORE
Charging
Circuit
VSIM
VRTC
VTCXO
VBAT
Pow er
Management
(ADP6522)
VANA
VMEM
VCORE
Charging control interface
LCD Module
Memory
Flash/SRAM
(64MB / 16MB)
Handfree input
USC Data Bus
Backlight
LED
V_LED
LCD Control Bus
Data Bus
Address Bus
BACKLIGHT
Vibrator
VBAT
LDO 3.0V
White LED
DRV 4.5V
VBAT
Li-Ion
Battery
P MOSFET
OverVoltage
Protect Circuit
LCD_PWR
V_LED
VMEM
HANDFREE IN
TX/RX
Power
Jack
EXTPWR
10.2. RF Block Diagram
RXI
LNA900I
RXI
GSM
RXQ
RXQ
LNA1800I
DC
T/
DC
DC
DC
LNA1900I
BASEBAND
ANTENNA SW
PC
LOGE
DATA,CLK
FrrcN PLL
UVTUN
FRE
UCP
GSM
26MHz
LOGE
VTCXO
DCS
PCS
TXI
CX77314
DI
TXI-
TXVC
TLCPO
CP
DI
90
TXQ
TXQ
CX74063
– 10–2 –
VSYN
[8]
[2]
[1]
VRF
[8]
RAMP
RF_TXEN
CPL
VTCXO
PCSRX
DCSRX
[8]
[8]
GSMRX
[8]
33p
C1143
C1180
15P
12p
L1152
NM
C1145
51k
R1193
C1141
39p
MM8430-2600
J1161
GND 6
GND 5
GND 4
GND 3
9
10
16
P_RX
D_RX
G_RX
U1141
C1181
68p
R1190
51.1
L1141
NM
C1185
NM
modify0512
L1161
15nH
3n9 L1142
0.5p
C1144
modify0529
L1162
15nH
JP
2
OUT
IN
1
AN1161
910
R1191
C1182
150p
R1192
51.1
SHS-L090TL
1
2
3
7
6
5
G
NC
VAPC
VCC
5
6
7
8
C1172
10p
C1171
33p
R1131
51
R1196
JP
C1108
10n
33p
C1155
3
1
6
E3D
C1107
100p
C1106
NM
4
5
– 11–1 –
JP
R1197
12
11
C1105
NM
10 GND
C1103
10n
1u/0603
C1174
4
3
2
1
3
1
6
C1102
33p
PEMB3
R1198
1k
ENA
VAPC
MAS9122
ENBC
OUTC
OUTA
4
5
2
8
5
6
7
1k2
R1199
10n/X7R
C1177
VREF
GND
VCC
2
3
4
33p
C1116
NM
C1115
C1101
- 220uF
R1103
1
+
E3D
10u/0805
C1178
2
R1102
E3D
220
R1101
C1114
JP
R1142
1k
C1156
12p
CX77314
VAPC
Vcmos
BS
U1101
BEAD
B1100
OUTB
4.7K
4.7K
C1113
33p
U1172
U1173
GND
VCC
C1110
C1112
NM
10n
1u/0603
C1175
4.7K
4.7K
6.8p
E3D
2
L1101
JP
C1111
PEMB3
U1171
L1102
4.7nH
C1184
33p
LDC15D19
U1131
G/I
G
D/I
C1131
NM
G/O
G
D/O
U1103 AD8315
FLTR
VSET
ENBL
RFIN
10p
C1173
4
14
R1195
JP
4
3
2
1
VC3
VC2
VC1
11
C1157
NM
22p
modify0512
E3D
C1154
CPL
DCS/PCS OUT
13
8
GND
GND
14
C1161
2
ANT
13
G_TX
7
D/P_TX
GND
GND
GND
GND
GND
GND
GND
1
3
5
6
8
12
15
4
ISO CPL
8
9
GSM OUT
GND
GND
15
7
16
6
VCC
VCC
5
DCS/PCS IN
GSM IN
1
4
modify0512
E3B
3
11.1. Circuit Diagram of RF Band-1
3
11. CIRCUIT DIAGRAM
4
1
2
C1176
1u/0603
PA_EN
VTX[
Mode
G_TX
D/P_TX
G/D_RX
P_RX
TRSW_PR
TRSW_DT
TRSW_GT
GSMTX
VAPC
BS
DCSTX
VBAT
Vc3
0
0
0
1
[1]
8]
Vc1 Vc2
1
0
0
1
0
0
0
0
[1]
[1]
[1]
[8]
[8]
[8]
C1252
180R
TP9 TP10
C1254
18p
C1253
33p
1
2
1
2
DCSRX
PCSRX
GSMRX
VRF
RXEN1
RF_TXEN
BS
VTCXO
DCSTX
GSMTX
1
VTX
1
VRF
B7740
IN
G
G OUT
U1272
B7744
IN
G
G OUT
4
3
4
3
4
3
10
15p
12p
C1267
JPE3C
modify 0529
L1261
8n2
L1272
3n9
L1271
3n9
C1271 E3C
0p5 modify 0529
C1272
0p5
C1265
15p
C1262
R1295
JP
C1250
2p7
C1247
10p
L1201
180n/0603 C1204
39p/NPO
E3B
modify0522
R1203
220/1%
C1248
33p
C1266
R1206
51
C1205
100p
R1207
NM
SAFSE942
IN
G
G OUT
U1271
1
2
U1261
510
390
R1205
R1204
C1202
39p/NPO
R1202
510/1%
C1249
33n
R1231
C1203
2.2n/X7R
L1241
27n
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
C1245
22p
RXENA
TXENA
PCO
VCXO_EN
PDETVCC
VCC1
TXCPO
TXINP
LNA900IN
GNDLNA900
LNA1800IN
PDET
LNA1900IN
NC
NC
C1246
100n
C1211
22p
L1211
82n
C1213
NM
– 11–2 –
C1212
NM
C1214 C1215
470p 470p
C1216
100n
CX74063
VDDBB
LE
CLK
DATA
XTALTUNE
SXENA
VCCFN_CP
UHFCPO
GNDFN
XTAL
VCCF
VCCD
GNDD
XTALBUF
LPFADJ
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
U1201
R1225
5k6
C1242
10u
C1221
22p
del C1222
E3B
R1221
39k/1%
C1229
220p
C1241
0.1u
C1244
100n
1
1
2
3
1
R1223
10
R1222
10
R1224
10
NM
R1296
C1223 C1224
22p
100n
100n
R4
E3D
C1226
10p
C1227
680p
1
R1226
2k
C1228
8n2/PC
B1241
BEAD
C1243
22p
TP5 TP6 TP7
B1222
BEAD
R1291
NM
VTCXO
R1292
100nF
1
4
B1221
BEAD
C1225
1n
GND Vc
o/p Vcc
U1291
modify0522
E3B
1
TP1 TP2 TP3 TP4
1
11.2. Circuit Diagram of RF Band-2
1
56
55
54
53
52
51
50
49
48
47
46
45
44
TXVCOTUNE
TX1800/TX1900
TX900
VCCTXVCO
VCC4
RXIP
RXIN
RXQP
RXQN
VCC3
VCCUHF
UHFTUNE
UHFBYP
PAVAPC
BBVAPC
TXIP
TXIN
TXQP
TXQN
TXIFP
TXIFN
VCC2
CAPIP
CAPIN
CAPQP
CAPQN
16
17
18
19
20
21
22
23
24
25
26
27
28
R1297 JP
TXQN
TXQP
TXIN
TXIP
VRF
13MHz_BB
BEAD
R1293
NM
C1291
VTX
10k
SXEN
C1230
100n
R1232
LE
CLK
DATA
VSYN
VRF
RXIP
RXIN
RXQP
RXQN
TP8
R1294
JP
1
3
2
1
AFC
C102
C103
TDO
1
1
1
TDI
1
TP123
TP_GPIO32
TMS
1
TCK
R102
10M/0603R
1
1
1
1
TP128
GPCS1
TP102
TP_GPIO14
TP105
TP_GPIO16
TP107
TP_GPIO17
TP108
TCK
TP109
TMS
TP110
TDI
TP111
TDO
1
TP104
TP_GPIO9
TP125
TP_GPIO11
1
1
TP126
TP_GPIO5
X101
MC-146
TBD
C113
0.1U /0402C
C104
C105
C106
C107
C108
C109
C110
C111
TBD
C114
ADD[1..22]
LCD_CTL
YMU_CS
LCD_NRST
LCD_ CS
BL_KEY
BL_LC D
YMU_AVCC _ON
VIB_ON
PJ_FUNC_ SEL
GPIO10
PJ_ACC_ IN
MIC_ON
YMU_IRQ
EOC
CHG_GAT E_IN
LC D_ID
CH G_EN
CHG_DET
NRESET
POW ER_ON
SYS_ PWR_ON
BBCLK
CLKON
KEYR OW_0
KEYR OW_1
KEYR OW_2
KEYR OW_3
KEYR OW_4
KEYC OL_0
KEYC OL_1
KEYC OL_2
KEYC OL_3
KEYC OL_4
ADD[1..22]
ADD1
ADD2
ADD3
ADD4
ADD5
ADD6
ADD7
ADD8
ADD9
AD D10
AD D11
AD D12
AD D13
AD D14
AD D15
AD D16
AD D17
AD D18
AD D19
AD D20
AD D21
AD D22
L14
F12
L13
M12
M5
C5
A7
D11
D10
B12
C11
D9
B11
A11
C10
D8
A10
C9
C7
B9
A9
B8
A8
D6
B7
H14
H13
J12
J11
N14
L12
G14
B3
A3
B2
E14
A6
F4
D4
B5
A5
C4
E4
B4
A4
C3
H4
J3
J2
J4
K3
K2
K4
L4
L1
L3
L5
M1
M2
N1
P1
N2
P2
N3
M3
P4
N4
M4
P5
VCO RE
AD6525
GPIO_32(WAIT)
SM_SW_SYNC (GPO_10)
GPCS1
GPCS0
nDISPLAYCS(LCDCTL)
BACKLIGHT1 (GPO_23)
BACKLIGHT0 (GPO_22)
GPIO_0
GPIO_1
GPIO_2
GPIO_3
GPIO_4
GPIO_5
GPIO_6
GPIO_7
GPIO_8
GPIO_9
GPIO_10
GPIO_11
GPIO_12
GPIO_13
GPIO_14
GPIO_15
GPIO_16
GPIO_17
GPIO_18
GPIO_19
GPIO_20
GPIO_21
RESET
CLKIN
CLKON
OSCOUT
OSCIN
PWRON
GSM_SW_DRV (GPO_11)
KEYPADROW0
KEYPADROW1
KEYPADROW2
KEYPADROW3
KEYPADROW4
KEYPADCOL0
KEYPADCOL1
KEYPADCOL2
KEYPADCOL3
KEYPADCOL4
ADD0
ADD1
ADD2
ADD3
ADD4
ADD5
ADD6
ADD7
ADD8
ADD9
ADD10
ADD11
ADD12
ADD13
ADD14
ADD15
ADD16
ADD17
ADD18
ADD19
ADD20
ADD21
ADD22(nDISPLAYCS)
U101
0.1U /0402C 0.1U /0402C 0.1U /0402C 0.1U /0402C 0.1U /0402C 0.1U /0402C 0.1U /0402C
SIMVCC VMEM
H1
P7
K14
C8
VCC1
VCC2
VCC3
VCC4
C101
L9
VSIM
0.1U /0402C 0.1U /0402C 0.1U /0402C
L2
N5
N9
N13
VMEM1
VMEM2
VMEM3
VMEM4
VMEM
– 11–3 –
C112
0.1U /0402C
VMEM
R101
(GPO_2)
(GPO_4)
(GPO_7)
(GPO_8)
(GPO_9)
JTAGEN
SIMDATAOP
SIMCLK
SIMRESET (GPIO_23)
SIMSUPPLY (GPIO_24)
SIMVPROG (GPIO_22)
USC0
USC1
USC2
USC3
USC4
USC5
USC6
BSDO
BSOFS
BSDI
BSIFS
VSDI
VSDO
VSFS
CLKOUT
CLKOUT_GATE
(VBCRESET)GPO_24
(ARSM)GPO_5
(ATSM)GPO_6
ASDI
ASDO
ASFS
TX_GSM (GPO_16)
ADD23(TX_DCS)GPO_17
(OTH_EN)GPO_18
(OTH_VLO_EN)GPO_19
(OTH_DATA)GPO_20
(OTH_CLK)GPO_21
(RXON)GPO_0
(TXON)GPO_1
GPO_3
TXPA
PA_NEGBIAS
TXPHASE
DCS_SW_SYNC
DCS_SW_DRV
RD
HWR
LWR
WE
ROMCS
RAMCS
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
DATA8
DATA9
DATA10
DATA11
DATA12
DATA13
DATA14
DATA15
0R/0402R
VRTC
E3
VPEG1
VCO RE
B14
B10
C6
D5
VEXT1
VEXT2
VEXT3
VEXT4
GND1
GND2
GND3
GND4
GND5
GND6
GND7
GND8
GND9
GND10
GND11
J1
K1
P3
L6
L8
P12
L11
C13
A12
D7
B6
A2
VDDRTC
VSSRTC
D3
K11
J13
K12
L10
K13
J14
C14
D12
A14
A13
E11
C12
B13
F3
G4
G2
G1
G3
H3
H2
D1
D2
E1
A1
C1
E2
F1
F2
E13
G11
E12
D14
D13
F11
B1
C2
G12
G13
H12
F14
F13
H11
M11
N12
P13
P14
M13
M14
N6
P6
M6
N7
M7
L7
P8
N8
M8
P9
M9
P10
N10
M10
P11
N11
+
1
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D[0..15]
SIM_IO
SIM_CLK
SIM_RESET
SIM_ON
SIM_PROG
US C0
US C1
US C2
US C3
US C4
US C5
US C6
BSDO
BSOFS
BS DI
BSIFS
VS DI
VSDO
VSFS
CLK_OUT
CLKOUT_GATE
VBC_RESET
ARSM
ATSM
AS DI
ASDO
ASFS
RD
HWR
LW R
WE
ROMCS
RAMCS
TP122
TP_JTAGEN
BAT101
SEIKO XH414H
TBD
R107
TBD
R103
VMEM
RF_TXEN
SXEN
LE
DATA
CLK
RXEN
TXEN
PA_EN
TRSW_DT
TRSW_PR
TRSW_GT
RXEN1
D[0..15]
2
4
1
3
2
4
1
3
11.3. Circuit Diagram of GSM Processor
1
1
R105
100K/0402R
R106
100K/0402R
VMEM
TP_CLKOUT
TP101
RXEN
TP124
1
1
TP118
TP_USC6
TP116
TP_USC5
TP114
TP_USC4
1
1
TP112
TP_USC3
US C1
US C2
TP115
TP_USC2
TP113
TP_USC1
1
1
TP106
TP_USC0
TP130
TX
1
1
TP129
RX
1
TP206
BSDO
TP208
BSOFS
TP207
BSIFS
TP205
BS DI
1
1
1
1
VBC_RESET
TXEN
RXEN
CLKOUT_GATE
CLK_OUT
ATSM
ARSM
BSIFS
BS DI
BSOFS
BSDO
VSFS
VS DI
VSDO
ASDO
ASFS
AS DI
TP_VBCRST
1
TP201
R201
100K/4P2R
R207
100K/4P2R
B4
A3
B2
B1
C2
C1
K1
K4
J4
K2
J2
K3
J3
E2
F1
F2
G2
D2
D1
E1
H1
H2
J1
IDACOUT
IDACREF
TDI
TDO
TMS
TCK
RESET
TXON
RXON
MCLKEN
MCLK
ATSM
ARSM
BSOFS
BSDO
BSIFS
BSDI
VSFS
VSDO
VSDI
ASDI
ASFS
ASDO
U201
100K/0402R
R213
VCO RE
VINAUXP
VINAUXN
VINNORP
VINNORN
REFOUT
REFCAP
AFCDAC
RAMPDAC
IRXP
IRXN
QRXP
QRXN
ITXP
ITXN
QTXN
QTXP
B7
B6
A4
B5
A5
A6
J6
K9
K6
– 11–4 –
AUXADC6
AUXADC5
AUXADC4
AUXADC3
AUXADC2
AUXADC1
BUZZER
VOUTAUXP
VOUTAUXN
K8
K7
H10
G10
J10
K10
A7
A8
A10
H9
E10
D10
C10
B10
F9
E9
C9
D9
0.1U /0402C
C213
C204
0.1U /0402C
ADC5
0.1U /0402C
C216
VANA
2.2U /0603C
R210
100K/0402R /1%
Charging T emp
VOUTAUXP
VOUTAUXN
VOUTNORP
VOUTNORN
VINAUXP
VINAUX N
C205
BUZZ ER
1
1
C207
C215
TP204
ADC6
TP203
ADC5
PCB_Temp
VANA
TP_BUZZER
TP202
RXIP
RXIN
RXQP
RXQN
TXIP
TXIN
TXQN
TXQP
0.1U /0402C
0.1U /0402C
0.1U /0402C
C206
VCO RE
BATTEMP
0.1U /0402C
C218
AFC
RAMP
VINNORP
VINNORN
0.1U /0402C
C212
R206
100K/0402R
C214
10nF/ 0402C
0.1U /0402C
C203
VANA
ADC6
C202
0.1U /0402C
C201
2.2U /0603C
VOUTNORP
VOUTNORN
VMEM
AD6521
G1
DVDD2
2
4
1
3
2
4
1
3
F10
AVDD1
NC(MICCAP)
NC(REFCAP2)
J8
J9
B9
A9
AVDD2
AGND4
AGND3
AGND2
AGND1
AVDD3
B3
J7
B8
G9
A1
DVDD1
DGND1
DGND3
A2
J5
K5
DVDD3
VANA
1
VMEM
0.1U /0402C
C217
NTC
11.4. Circuit Diagram of Voiceband, Baseband and Codec
BAT_VOLTAGE
VANA
R212
100K/N TC/0402R
R211
200K/0402R /1%
100K/N TC/0402R
R209
R208
200K/0402R /1%
NTC
P_JACK
CON3 02
2
1
BATTEMP
2
1
TP_GND
TP302
1
TP_VBAT
F302
3
2
1
FULSE/0603
C310
2.2U /25V/0805C
C325
39pF
T301
2
1
1
1
CRS03
U312
BAT_CON
GND
BAT_TEMP
VBAT
2
2
1
CON3 01
R310
10K
U306
BLM55C9V1
4
2
U308
6
EMD2
3
5
CLKON
R311
TBD
C322
0.1U
C309
TBD
1
C301
4.7U /0805C
– 11–5 –
1
GND
A
Y
VCC
4
5
1M/0402R
R307
U301
GATEDR
ISENSE
CHRIN
GATEIN
SIMVSEL
CHGEN
TCXOEN
SIMEN
ROWX
PWRONKEY
PWRONIN
VRTCIN
BATSNS
VBAT2
VBAT
2
R3
TBD
C318
68pF
VBAT
REFOUT
RESCAP
RESET
CHRDET
EOC
VTCXO
VSIM
VMEM
VCORE
VAN
VRTC
MVBAT
2.2uH /060 3R
L301
VTCXO
C323
0.1U
CRS03
U311
C317
10N/040 2C
1
ADP3522XCP-3.0
9
12
7
10
8
14
28
1
31
30
29
2
4
19
22
C312
10N/040 2C
U305 NC7SZU04P5X
3
2
D
U309
SI3443DV
1
2
5
6
C321
0.1U
4
R303
0.3/0805R
CHG_GAT E_IN
SIM_PROG
CH G_EN
CLKON
SIM_ON
KEYR OW_4
VBAT
C302
0.1U /0402C
R301
100K/0402R
TP303
POW ERON_ KEY
VBAT
POWERON_ IN
10N/0402
R314
1
TP305
CHG_GAT E_IN
U307
FDC640P
4
1
2
5
6
1
POWER_KEY
R302
100K/0402R
TP306
CH G_EN
3
DAN2 22
13MHz_BB
R309
10K
C319
0.01U /040 2C
1
SYS_ PWR_ON
1
2
U302
POW ER_ON
22 K
27
TP301
22 K
VBAT
3
AGND
11.5. Circuit Diagram of Power Management System
3
24
32
17
NC
NC
NC
DGND
11
26
15
16
6
13
25
18
20
21
23
3
5
18pF
C324
TP304
EOC
NRESET
C311
0.1U /0402C
0R
R313
VTCXO
SIMVCC
VMEM
VCO RE
VANA
VRTC
BAT_VOLTAGE
1
BBCLK
CHG_ DET
EOC
VMEM
VRTC
CHR_ DET
1
C304
4.7U /0805C
C307
2.2U/0805
SIMVCC
TP307
C306
4.7U /0805C
C303
0.1U /0402C
VANA
C308
1U/0603C
VTCXO
C305
4.7U /0805C
VCO RE
VMEM
D[0..15]
8
7
6
5
VMEM
GPIO10
NRESET
RD
HWR
LW R
WE
ROMCS
RAMCS
0R/8P4R
R401
D[0..15]
0R/0402R
TBD
R407
R406
WP -ACC
CI Os
CI Of
CE2 s
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
G8
E5
D5
H3
D4
C4
C6
H2
J2
C5
K6
H9
D6
J3
G4
K4
H5
H6
K7
G7
J8
K3
H4
J4
K5
J7
H7
K8
H8
C401
AMD (64+16PS)
SA
RY/BY
RESET
OE
UB
LB
WE
CEf
CE1s
WP/ACC
CIOs
CIOf
CE2s
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15/A-1
U401
0.1U /0402C
J5
J6
F9
ADD1
ADD2
ADD3
ADD4
ADD5
ADD6
ADD7
ADD8
ADD9
AD D10
AD D11
AD D12
AD D13
AD D14
AD D15
AD D16
AD D17
AD D18
AD D19
AD D20
AD D21
AD D22
– 11–6 –
SIM_CLK
SIM_RESET
ADD[1..22]
R404
150R/1%/0402
TP_SIMCLK
TP403
C405
22pF
TP_SIMRST
TP402
TP_SIMVCC
1
TP401
C402
TBD
SIMVCC
CLK
RST
VCC
J401
C403
0.1U /0402C
1
3
5
R405
100K/0402
2
4
6
SIM SOCKET
I/O
VPP
GND
R403
10K/0402
C404
33pF
1
TP_SIMIO
NC0
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
G2
F2
E2
D2
F3
E3
D3
C3
C7
E7
F7
C8
D8
E8
F8
D9
G9
F4
E4
D7
E6
E9
ADD[1..22]
TP404
VCCf
VCCs
VSS
VSS
1
2
3
4
VMEM
1
11.6. Circuit Diagram of Memory & SIM
1
G3
J9
1
SIM_IO
TP405
GND
YMU_AVCC _ON
0R/0402
R522
C527
TBD/0402
N O
I
C G
100K
U505
4
5
ADD[1 ..2 2]
YMU_CS
RD
WE
YMU_VIB
YMU_IRQ
NRESET
CLK_OUT
C513
0.1U /0402C
ADD2
C528
0.01U
VR EF
C519
0.1U
C526
4.7U/0805
YMU_AVCC
C512
0.1U
YMU_AVCC
C525
2.2U/0603
ADD[1..22]
C530
0.1U /0402C
VMEM
VOUTAUXN
SC1563ISK-3.0
1
2
3
2
19
3
4
1
8
16
32
7
5
6
EXT1
EXT2
/IRQ
/RST
CLKI
VSS
SPVSS
YMU762(MA3L2)
SDOUT(IOVDD)
VDD
IFSEL(NC)
PLLC
U506
C529
TBD
VOUTNORN
VOUTNORP
9
VREF
10
11
18
17
14
13
20K/0402R
R508
– 11–7 –
HPOUT-L/MONO
HPOUT-R
SPOUT2
SPOUT1
EQ3
EQ2
10N/040 2C
C517
I/O 6
I/O 4
GND2
1
6
4
5
D[0..15]
TP503
HPOUT_R
HPOUT
200P/0402C
C518
0.1U /0402C
C521
33P/0402C
C532
U507 ESDA
I/O 3
GND1
I/O 1
D[0..15]
47K/0402R
R509
10K/0402R
R514
R510
TBD
C520
TBD/0402
C523
33P/0402C
3
2
1
C531
C524
SPK1
33P/0402C 33P/0402C
0R/0402R
R504
0R/0402R
R503
SDIN(/CS)
SCLK(/RD)
/WR
SYNC(A0)
29
31
28
30
VBAT
15
SPVDD
R521
12
EQ1
D0
D1
D2
D3
D4
D5
D6
D7
27
26
25
24
23
22
21
20
D0
D1
D2
D3
D4
D5
D6
D7
33P/0402C
C515
BUZZ ER
TBD/0402C
C522
SPK2
T503 - B (TBD)
1
2
C516
33P/0402C
C511
TBD/0402C
SPK2
SPK1
TP502
TP_SPK-N
1
T504 - B (TBD)
1
2
T502(TBD)
1
2
11.7. Circuit Diagram of Audio 1
T501(TBD)
1
2
TP501
TP_SPK-P
SPEAKER
LS501
1
RECEIVE R - B
LS502
VINAUXN
VINAUXP
VOUTAUXP
HPOUT
0.1uF
C614
MIC_ON
33P/0402C
C610
C624
100P/0402
0R
R611
N O
I
C G
4
5
0.1U
33P/0402C
C611
R629
TBD/0402R
C620
0R
R620
R610
1M
R609
1M
YMU_AVCC
LP2985AIMX5-2.5
R615
47K
C629
2.2U /0603C
1
2
3
R623
0R
C602
10U/0805C
TBD/0402C
C612
R606
1.2K /1%
R630
0R
MIC_PWR
10uF/0805
C628
10uF/0805
C616
C630
2.2uF/0603
10N/040 2C
C601
2.4K/0402R
C622
0.1U /0402C
R625
0R
C626
10U/080 5C
MIC_PWR
US C1
C627
0.1U /0402C
R643
0R
3
2
1
0
1
S
A
VCC
– 11–8 –
EXT_MIC
NC7SB3157
B0
GND
B1
U603
PJ_FUNC_ SEL
4
5
6
R642
TBd
US C6
US C2
PJ_ACC_ IN
VINNORN
VINNORP
100K
R640
C615
33P/0402C
VMEM
8.2K
R641
0.1U
C631
C607
33P/0402C
C623
100P/0402
R639
1MR
C608
33P/0402C
0.1U
C621
T607 - B (TBD)
1
2
MIC_PWR
R632
TBD
R633
100K/0402R
VMEM
MIC/ RX
3
2
1
TX
I/O 6
I/O 4
GND2
I/O 4
GND2
I/O 6
GND
4
5
6
U605 ESDA
I/O 3
GND1
I/O 1
U604 - B ESDA
I/O 3
GND1
I/O 1
3
2
1
C603
0.1U /0402C
SPK
R637
100K/0402R
R603
0/0402R
C605
TBD/0402C
R602
4.7K/0402R
MIC_PWR
TBD/0402C
C606
0R
R621
R628
TBD/0402R
R624
0R
T604 - B (TBD)
1
2
R626
T605 - B (TBD)
1
2
U601
T606 - B
1
2
VBAT
T601 - B (TBD)
1
2
T602(TBD)
1
2
11.8. Circuit Diagram of Audio 2
T603(TBD)
1
2
4
5
6
MIC/RX
GND
TX
SPK
ACC_ IN
1
2
TP_MIC
TP601
1
4
6
5
3
2
PHONEJ ACK-B
J601
MICROPH ONE - B
MIC601
1
D702
LE D - B
D701
LE D - B
BL_KEY
LE D - B
LE D - B
R714
200R /8P4R - B
D704
D703
V_LED
JP702
1
2
3
N/C
KEYROW_3
KEYCOL_4
KEYROW_0
KEYCOL_3
KEYROW_1
KEYCOL_2
KEYROW_2
KEYCOL_1
KEYCOL_0
POWER_KEY
GND
N/C
U706
C736
2.2U /0603C
1
2
3
N O
I
C G
U703
4
5
LE D - B
LE D - B
R702
TBD - B
D707
D706
LE D - B
D709
10N/040 2C
C735
R705
1K/0402R - B
1
1
2
6
E2
B2
C2
FFB2222A - B
E1
B1
C1
U702
R713
100R /1%/0402R - B
LE D - B
D710
M701
TP24
LCD_NRST
TP25
WE
3
4
5
+
-
A
D[0..15]
1
1
– 11–9 –
3
TP12
Vibrator SIG
100R /0402R - B
R706
1
TP29
VIB_PW R
ADD2
DAN222 - B
1
2
U705
TP21
D8
TP20
D9
TP19
D10
TP18
D11
C745
R710
100K
R709 100K
YMU_VIB
VIB_ON
R711
TBD
R712
TBD
6
5
3
4
EN
CX8
VIN
CD4
U704
2
9
10
7
1
V_LED
18pF
C748
SC600BIMLTR, 5V_ 60M A
CF1+
CF1CF2+
CF2-
VOUT
18pF
C744
C747
C743
C746
C742
1
1
1
1
1
1
1
1
1
1
1
TBD - B 0.1uF - B TBD - B TBD - B TBD - B 18pF
C741
D15
D14
D13
D12
D11
D10
D9
D8
TP13
LCD_CTL
TP22
LCD_ CS
TP23
ADD2
TP17
D12
TP16
D13
TP15
D14
TP14
D15
LCD_CTL
LCD_ CS
C754
10U/080 5C
VBAT
WE
R708
TBD - B
LCD_PWR
1SS355
D713
1
D[0..15]
ADD[1..22]
BL_LC D
10K - B
R707
ADD[1 ..2 2]
R704
8.2R/0805R - B
VBAT
LCD_NRST
TP28
LCD_ PWR
LG COIN M OTOR
C737
10U/0805C
LCD_PWR
R701
100R /1%/0402 R - B
LE D - B
D708
LP2985AIMX5-3.0
VBAT
KEYPAD_HOT BAR - B
12
1
2
3
4
5
6
7
8
9
10
11
13
VBAT
LE D - B
D705
1
2
3
KEYR OW_3
KEYC OL_4
KEYR OW_0
KEYC OL_3
KEYR OW_1
KEYC OL_2
KEYR OW_2
KEYC OL_1
KEYC OL_0
POWER_KEY
8
7
6
5
1
2
3
4
VMEM
11.9. Circuit Diagram of User Interface
8
7
6
5
1
2
3
4
2
1
GND
8
33pF
C750
C739
1U/0603C
C738
1U/0603C
18pF
C749
LC D_ID
18pF
C753
C755
TBD
TP30
V_LED
33pF
C752
1
C740
1U/0603C
TP27
GND
1
33pF
C751
C701
VEE
VEE
VDD
VDD
SEL68
VSS
RD(E)
D7
D6
D5
D4
D3
D2
D1
D0
CS
RS
RESB
WR
VSS
VSS
CA_LED
CA_LED
AN_LED
AN_LED
N/C(VOUT)
U701
C733
0.1U /040 2 -B
C7
33P/0402C
R716
TBD
R715
0R
1
TP701
LCD_ ID
Wintek DX1209K-6C LWa - B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
2.2U /060 3 -B
LCD_PWR
11.10. Circuit Diagram of Keypad
SW716
KEY [#]
SW711
KEY [0]
SW706
KEY [*]
SW701
2
2
2
2
1
2
1
1
1
1
2
2
2
2
KEY [SEND]
SW717
KEY [9]
SW712
KEY [8]
SW707
KEY [7]
SW702
POWERKEY & END
SW718
SOFTKEY_RIGHT
1
1
1
1
1
1
1
KEY [6]
SW713
KEY [5]
SW708
KEY [4]
SW703
2
2
2
1
1
1
2
2
2
– 11–10 –
KEY [3]
SW714
KEY [2]
SW709
KEY [1]
SW704
1
1
1
2
2
2
SOFTKEY_LEFT
SW715
KEY_[DOWN]
SW710
KEY_[UP]
SW705
POWER_KEY
KEYROW_3
KEYROW_2
KEYROW_1
KEYROW_0
KEYCOL_0
KEYCOL_1
KEYCOL_2
KEYCOL_3
KEYCOL_4
D2
R300
640
0
S3KV
84VD23381FJ-80
AD6525ACA
ADP3522
N
43
H
L00A
– 12–1 –
227
LUNA 600B
Z3
Z1
12.1. Main PCB
Z3
9122
12. LAYOUT DIAGRAMS
26
800Z
6330
Y762C
S3KV
Z1
Z1