Download Owner / Calibration Manual

Transcript
Model 8903B
General Information
lbble 1-2. Supplemental Information
All parameters describe performance in automatic operation or with properly set manual controls.
SOURCE
Frequency Switching Speed: <3 ms (does not include
HP-IB programming time).
Sweep Mode: Logarithmic sweep with up to 500
points/decade or 255 Points total between entered start
stop frequencies.
Output Level Switching Speed: 20 ms (does not include
HP-IB programming time.
Typical Source to Analyzer Isolation (Option 001 only)
System distortion and noise can be degraded when driving
low impedance loads (with source output impedance in the
50R mode) due to coupling from the source output to the
analyzer input. See Figure 1-7 for the plot of various load
impedances vs frequency.
MEASUREMENT
SINAD
Detection: True rms or rms calibrated average.
Resolution: 0.01 dB for ratios >25 dB. For ratios <25
dB, the display is rounded to the nearest half dB to reduce digit flickering with noisy signals. (Full resolution is
available by defeating this feature using Special Function
16.1 .)
Analog Meter* active in SINAD only and for SINAD
ratios 518 dB (or 524 dB using Special Function 7.1).
Accuracy: 1 dB typical.
Tuning: notch filter is tuned to analyzer source frequency.
Time to Return First Measurement: 1.5s typical.
Measurement Rate: 2.0 readingsls typical.
SIG/NOISE
Resolution: Same as SINAD.
Measurement Rate: One readinglsecond for rms and
average detectors (one reading/2 seconds for quasipeak detector).
Detection: True rms or rms calibrated average or quasipeak.
Time of Return First Measurement: ~ 2 . 5 stypical.
Operation: The Audio Analyzer displays the ratio of the
input voltages as the internal source is switched on and
Off.
DISTORTION
3 dB Measurement Bandwidth: 10 Hz to 500 kHz
Detection: True rms or rms calibrated average.
Displayed Resolution:
0.0001% (<0.1% distortion)
0.001% (0.1% to 3% distortion)
0.01OO/ (3% to 30% distortion)
0.1YO(>30% distortion)
Time to Return First Measurement: 1.5s typical.
Measurement Rate: 2 readings/s typical.
~~
AC LEVEL
AC Converter: True rms responding detection for signals with (crest factor of 53), rms calibrated average detection, quasi-peak detection (Meets CClR 468-3
standard.)
3 dB Measurement Bandwidth: >500 kHz.
Time to Return First Measurement: ~ 1 . 5 typical.
s
Measurement Rate: 2.5 readings/s for rms and average
detectors.
Quasi-peak Detector Accuracy: (20 Hz to 20 kHz)
f6%.
DC LEVEL:
s
Time to Return First Measurement: ~ 1 . 5 typical.
Measurement Rate: 3 reading/s.
FREQUENCY MEASUREMENT
Measurement Rate: same as measurement mode selected.
Counting Technique: reciprocal with 2 MHz time base.
AUDIO FILTERS
400 Hz High-Pass Filter Rejection: >40 dB at 240 Hz;
>65 dB at 60 Hz.
REAR-PANEL INPUTS AND OUTPUTS
Recorder Outputs:
X Axis: 0 to 10 Vdc corresponding to the log of the oscillator frequency.
Output Resistance: 1kR
Y Axis: 0 to 10 Vdc corresponding to the displayed value
and entered plot limits
Output Resistance: 1 kR
Pen Lift: TIL output
Monitor Output:
Output Impedance: 600R
In ac level mode, provides scaled output of measured
input signal
In SINAD, distortion, and distortion level modes, provides scaled output of input signal with the fundamental
removed.
~~
The meter has hysteresis. The trip point for the 24dB range is > 18 dB, and the trip pont for the 18-dB range is <17 dB.
1-22
rev.30DE C88