Download AS-i 3.0 Command Interface

Transcript
AS-i 3.0 Command Interface
Table of contents
Table of contents
AS-i 3.0 Command Interface
1
Introduction........................................................................................... 7
2
Structure of the Command Interface .................................................. 8
2.1
3
List of all Commands ......................................................................... 10
4
Commands of the Command Interface............................................. 14
4.1
4.1.1
4.1.2
4.1.3
4.1.4
4.1.5
4.1.6
4.1.7
4.1.8
4.1.9
4.2
4.2.1
4.2.2
4.2.3
4.2.4
4.2.5
4.3
4.3.1
4.3.2
4.3.3
4.3.3.1
4.3.3.2
4.3.3.3
4.3.3.4
4.3.3.5
4.3.3.6
4.3.3.7
4.3.3.8
4.3.3.9
4.3.3.10
4.3.3.11
Issue date: 7.6.2013
Result-code values .......................................................................................... 9
4.3.3.12
4.3.3.13
4.3.3.14
4.3.3.15
AS-i 16-bit data............................................................................................... 14
Overview of the commands ......................................................................................... 14
Read 1 16-bit Slave in.Data (RD_7X_IN)...................................................................... 14
Write 1 16-bit Slave out. Data (WR_7X_OUT) ............................................................. 15
Read 1 16-bit Slave out. Data (RD_7X_OUT) .............................................................. 15
Read 4 16-bit Slave in. Data (RD_7X_IN_X) ................................................................ 16
Write 4 7.3 Slave out. Data (WR_7X_OUT_X).............................................................. 16
Read 4 7.3 Slave out. Data (RD_7X_OUT_X)............................................................... 17
Read 16 channels 16-bit Slave in. Data (OP_RD_16BIT_IN_CX)............................... 18
Write 16 channels 16-bit slave out. Data (OP_WR_16BIT_OUT_CX)........................ 19
Commands acc. to Profile S-7.4/S-7.5.......................................................... 20
Overview of the commands ......................................................................................... 20
WR_74_75_PARAM ....................................................................................................... 20
RD_74_75_PARAM........................................................................................................ 21
RD_74_75_ID ................................................................................................................. 22
RD_74_DIAG .................................................................................................................. 23
Acyclic commands ........................................................................................ 24
Overview of the commands ......................................................................................... 24
WRITE_ACYCLIC_TRANS ............................................................................................ 24
READ_ACYCLIC_TRANS.............................................................................................. 27
Structure of the response buffer................................................................................... 28
Command 1: Read „S-7.4 ID String" ............................................................................ 30
Command 2: Read „S-7.4 Diag String" ........................................................................ 30
Command 3: Read „S-7.4 Param String" ..................................................................... 30
Command 4: Write „S-7.4 Param String“ ..................................................................... 31
Command 5: „Transfer S-7.5“ ...................................................................................... 31
Command 6: Read „Cyclical S-7.5 16-bit configuration“ .............................................. 32
Command 7: Read „Safety monitor diagnostic (sorted acc. to OSSD)“ ....................... 33
Command 8: Read „Safety monitor diagnostic unsorted“ ............................................ 35
Command 9: „Diagnosing the Safe Link “ .................................................................... 36
Commands 10 and 12:
read "Current safety monitor diagnostic" .................................................................... 36
Commands 11 and 13:
read "Current safety monitor shutdown-history" ......................................................... 39
Command 14: Read "Safety monitor diagnostic" ......................................................... 41
Command 15: "Safety Status"...................................................................................... 43
Command 16: Read "Device index identifier" .............................................................. 45
3