Download Electronic Component Ordering R32C Web Server

Transcript
AUDIO & VIDEO
New Developments in Class D
reduced EMI and no output filter
By Thijs Beckers (Elektor Netherlands Editorial)
There’s no stopping technological progress,
including Class D amplifier technology.
New developments reduce the amount of
electromagnetic interference (EMI) and enable
amplifiers to work without an output filter. Read
more to learn how clever designers managed to
pull this off.
(see Figure 2). Increasing the switching frequency improves the
match between the output signal and the original signal. Unfortunately, high switching frequencies create all sorts of problems, such
as interference and high switching losses. Consequently, a switching frequency in the range of 250 kHz to 1.5 MHz is commonly used,
depending on the application.
The PWM signal is passed through a low-pass filter to recover the
original signal in amplified form. The switching pulses are largely filtered out, leaving the ‘average’ value. The necessary filter not only
increases the cost and the amount of space required on the PCB,
but also increases the likelihood of distortion due to nonlinearities
in the filter.
Filter-free
+UB
comparator
RL
inverter
-UB
triangular
wave
generator
040102 - 15
Figure 1. Simplified schematic diagram of a Class D amplifier.
Thanks to their high efficiency, Class D amplifiers are ideal for
compact and portable applications. However, conventional Class
D amplifiers need an external low-pass filter to recover the audio
signal from the pulse-width modulated signal (see below). In addition, they often lead to EMI problems, and the distortion level
(THD+N) is not especially good. However, advanced techniques
are used in modern Class D amplifiers to overcome these problems
and eliminate the need for an output filter, which not only reduces
the amount of space necessary on the PCB but also in many cases
reduces the overall cost of the compact or portable system.
Class D
First let’s have a brief look at how Class D technology works. A
Class D amplifier does not simply amplify the input signal as is (see
Figure 1). Instead, it uses a technique called pulse-width modulation
(PWM). The output voltage is proportional to the width of the pulse
36
Due to the ongoing demand for circuits that are even more compact and provide even better performance, circuit techniques that
do not require an output filter have been developed. An example
is the technique used in the Maxim MAX9700 (see the schematic
diagram in Figure 3).
This technique works as follows. Each push-pull output stage has its
own comparator, so each output stage can be driven separately. The
comparators are driven by differential audio signals and a shared
sawtooth generator. When the outputs of both comparators are
low, the two outputs of the Class D amplifier are both High. At the
same time, the output of the NOR gate is High, but this signal is
delayed by the RC network RON / CON. When the delayed output of
the NOR gate exceeds a certain threshold level, switches S1 and S2
are closed. This causes OUT+ and OUT– to both go Low until the
start of the next sampling interval. As a result, the two outputs are
active (High) for only a minimum period tON(min). The duration of this
period is determined by the values of RON and CON.
If the signal level at the input is zero, the OUT+ and OUT– outputs
are exactly in phase and the pulse width is tON(min). When the amplitude of the audio signal at the input varies, the two comparators
trigger at different times. In combination with the minimum tON
circuit, this causes the pulse width of one output to vary while the
pulse width of the other output remains the same (tON(min)). The average value of the signal present on each of the outputs corresponds
to a half-wave rectified version of the audio signal. The difference
between the two average values on the outputs forms the full audio
signal.
As the outputs are in phase when the input signal is zero, there is no
difference signal across the load under this condition and the power
consumption is minimal, all without any need for an output filter.
The circuit also makes use of the impedance of the connected loudspeaker. This impedance consists of a real part (Re) and an inductive part (Le) where the subscript ‘e’ indicates the electrical component They effectively form a first-order low-pass filter with a corner
frequency
fc = 1 / (2πLe/Re) [Hz].
11-2009
elektor