Download PC Cards CIFX 104

Transcript
Descriptions and Requirements
3.5
31/171
Requirements for Operation of the PC Cards cifX
Operating the PC cards cifX properly, the following described requirements
must be fulfilled.
Protocols
EtherCAT Slave,
EtherCAT Master,
EtherNet/IP Adapter (Slave),
EtherNet/IP Scanner (Master),
Open-Modbus/TCP,
POWERLINK-Controlled-Node/Slave,
PROFINET IO Device (Slave),
PROFINET IO Controller (Master)
Software
Installation
1. Driver for the Host Interface
Host Interfaces: PC/104
• The device driver cifX Device Driver must be installed (from V1.0.x.x).
®
If you install the device into a PC, in general Windows will be available as operating system. In this
case the cifX Device Driver must be installed to communicate to the device and to exchange data via
the dual-port memory,.
sercos Slave,
sercos Master,
VARAN Client (Slave)
PROFIBUS DP Slave,
PROFIBUS DP Master,
PROFIBUS MPI Device,
CANopen Slave,
CANopen Master,
DeviceNet Slave,
DeviceNet Master,
CC-Link Slave
Important! Upgrade older versions of the cifX Device Driver necessarily on the current
version indicated in section Driver and Software on page 10.
OR
• If Windows® is not available as operating system, an own driver must be developed using the cifX
Driver Toolkit and this driver must be installed.
®
• For the operating systems Linux, Windows CE, VxWorks, QNX and IntervalZero RTX ™ you can
buy Device Driver at the company Hilscher Gesellschaft für Systemautomation mbH
http://www.hilscher.com/.
2. The configuration software SYCON.net or alternatively the simple Slave configuration tool netX
Configuration Tool must be installed or another application program by which the PC card cifX
(Slave) can be parameterized.
How to use the
Software
On how to use the software for the configuration, the firmware download and for the diagnosis, note
the following notice:
Important! The USB interface, the serial interface as well as the cifX Device Driver may
only be used exclusively by one software, that is
- the SYCON.net configuration software (with integrated ODMV3) or
- the netX Configuration Tool or
- the cifX Test Application or
- the cifX Driver Setup Utility or
- the application program.
Never use the listed software simultaneously, otherwise this will result in communication
problems with the device.
If the SYCON.net configuration software was used on the PC, then stop the ODMV3
service before you use one of the other software listed above. Therefore, select Service
> Stop from the context menu of the ODMV3 system tray icon.
Firmware
Download
3. Using the configuration software SYCON.net or for the Slave alternatively the Slave configuration
tool netX Configuration Tool, the user must select and download the firmware to the PC card cifX.
Parameter
Setting
4. The PC card cifX must be parameterized using one of the following options:
• Configuration Software SYCON.net
• alternatively Slave configuration tool netX Configuration Tool (only Slave)
• Application program (programming required)
Communication
5. For the communication of a PC card cifX (Slave) a Master device for the respective communication
system is required. For the communication of a PC card cifX (Master) a Slave device for the
respective communication system is required.
Hardware
Installation
Environmental
Conditions
Important! Operating the PC cards cifX with Cable Connector Ethernet or with the Cable
Connector Fieldbus (label “\F” in its device name) requires proper connection of the
Ethernet (AIFX-RE), PROFIBUS (AIFX-DP), CANopen (AIFX-CO), DeviceNet (AIFX-DN)
or CC-Link (AIFX-CC) assembly interface to the basic card!
Due to a plug element from ERNI the lower limit of the operating temperature for all PC cards cifX
Real-Time Ethernet is 0 °C. This applies to all hardware revisions of the PC card cifX Real-Time
Ethernet.
Table 19: Requirements to operate PC Cards cifX properly
PC Cards cifX PC/104 | Installation, Operation and Hardware Description
DOC120206UM44EN | Revision 44 | English | 2015-07 | Released | Public
© Hilscher, 2008-2015