Download LPC32x0

Transcript
D
D
D
D
D
R
R
R
R
R
D
R
R
FT
FT
FT
FT
A
A
A
A
R
R
D
D
D
D
R
R
A
FT
FT
FT
A
A
R
R
D
D
D
R
A
D
FT
FT
A
A
R
R
D
b) Registers marked ‘S’ for access allows individual bits to be set to ‘1’ for each corresponding register bit. Bits set to ‘0’ will not affect
the value of the corresponding register bit. Reading an ‘S’ marked register will return an invalid value.
F
FT
FT
A
A
R
R
D
D
D
The R/W column in Table 15–332 lists the accessibility of the register:
a) Registers marked ‘R’ for access will return their current value when read.
FT
FT
FT
FT
FT
LPC32x0
Chapter 15: LPC32x0 USB device controller
[1]
A
A
A
A
A
NXP Semiconductors
D
D
c) Registers marked ‘C’ for access allows individual bits to be cleared by writing a value that has bits set to ‘1’ for each corresponding
register bit that needs to be set to ‘0’. Bits set to ‘0’ will not affect the value of the corresponding register bit. Reading a ‘C’ marked
register will return invalid value.
R
A
FT
D
d) Registers marked ‘R/W’ allow both read and write.
R
A
3.6 USB device register definitions
3.6.1 USB Device Interrupt Status Register - (USBDevIntSt - 0x3102 0200, R)
Interrupt status register holds the value of the interrupt. ‘0’ indicates no interrupt and ‘1’
indicates the presence of the interrupt.
Table 335. USB Device Interrupt Status Register - (USBDevIntSt - 0x3102 0200, R)
Bits
Name
Function
Reset value
31:10
-
Reserved
0x0
9
ERR_INT
Error Interrupt. Any bus error interrupt from the USB device. Refer to 0
section Section 15–3.8.1.9 “ReadErrorStatus”.
8
EP_RLZED
Endpoints realized. Set when Realize endpoint register or Maxpacket 0
size register is updated.
7
TxENDPKT
The number of data bytes transferred to the FIFO equals the number 0
of bytes programmed in the TxPacket length register.
6
RxENDPKT
The current packet in the FIFO is transferred to the CPU.
0
5
CDFULL
Command data register is full (Data can be read now).
0
4
CCEMPTY
The command code register is empty (New command can be written). 1
3
DEV_STAT
Set when USB Bus reset, USB suspend change or Connect change
event occurs. Refer to section Section 15–3.8.1.6 “Set Device
Status”.
0
2
EP_SLOW
This is the Slow interrupt transfer for the endpoint. If an Endpoint
Interrupt Priority Register bit is not set, the endpoint interrupt will be
routed to this bit.
0
1
EP_FAST
This is the fast interrupt transfer for the endpoint. If an Endpoint
0
Interrupt Priority register bit is set, the endpoint interrupt will be routed
to this bit.
0
FRAME
The frame interrupt occurs every 1 ms. This is to be used in
isochronous packet transfer.
0
3.6.2 USB Device Interrupt Enable Register - (USBDevIntEn - 0x3102 0204, R/W)
If the Interrupt Enable bit value is set, an external interrupt is generated (on Fast or Slow
Interrupt line) when the corresponding bit in the interrupt status register is set. If it is not
set, no external interrupt is generated but interrupt will still be held in the interrupt status
register. The bit field definition is same as the device interrupt status register as shown in
Table 15–335. All bits of this register are cleared after reset.
<Document ID>
User manual
© NXP B.V. 2008. All rights reserved.
Rev. 00.26 — 20 November 2008
361 of 719