Download User Manual - Nisuta.com

Transcript
User Manual
NS‐WMR54M
Contents
1
Introduction ........................................................................................................ 1
1.1
Packing List ........................................................................................... 1
1.2
Safety Precautions ................................................................................ 1
1.3
LEDs and Interfaces .............................................................................. 2
1.4
System Requirements ........................................................................... 4
1.5
Features ................................................................................................ 5
2
Hardware Installation ......................................................................................... 6
3
About the Web Configuration ............................................................................. 9
3.1
Access the Router ................................................................................. 9
3.2
Wizard ................................................................................................. 10
3.3
3.4
3.5
3.6
Status................................................................................................... 24
3.3.1
System...................................................................................... 25
3.3.2
LAN........................................................................................... 25
3.3.3
WLAN ....................................................................................... 25
3.3.4
WAN ......................................................................................... 26
3.3.5
Port Mapping ............................................................................ 26
3.3.6
Statistics.................................................................................... 27
3.3.7
ARP Table................................................................................. 28
Network ............................................................................................... 28
3.4.1
LAN........................................................................................... 29
3.4.2
WAN ......................................................................................... 35
3.4.3
WLAN ....................................................................................... 41
Service................................................................................................. 49
3.5.1
DNS .......................................................................................... 49
3.5.2
Firewall ..................................................................................... 51
3.5.3
UPNP........................................................................................ 58
3.5.4
IGMP Proxy .............................................................................. 59
3.5.5
TR-069...................................................................................... 59
3.5.6
ACL........................................................................................... 61
Advance............................................................................................... 64
3.6.1
Bridge Setting ........................................................................... 64
3.6.2
Routing ..................................................................................... 65
3.6.3
Port Mapping ............................................................................ 68
3.6.4
QoS........................................................................................... 69
i
3.7
3.8
3.6.5
SNMP ....................................................................................... 71
3.6.6
Others ....................................................................................... 72
Admin .................................................................................................. 73
3.7.1
Commit/Reboot......................................................................... 73
3.7.2
Upgrade .................................................................................... 74
3.7.3
System Log............................................................................... 75
3.7.4
Password .................................................................................. 76
3.7.5
Time Zone................................................................................. 77
3.7.6
Logout....................................................................................... 78
Diagnostic............................................................................................ 78
3.8.1
Ping........................................................................................... 78
3.8.2
ATM Loopback.......................................................................... 79
3.8.3
ADSL ........................................................................................ 79
3.8.4
Diagnostic Test ......................................................................... 80
ii
1
Introduction
The NS-WMR54M
is an ADSL access device that supports multiple line modes.
It provides one 10/100Base-T Ethernet interface at the user end. The device
provides high-speed ADSL broadband connection to the Internet or Intranet for
high-end users, such as net cafes and office users. The device provides high
performance access to the Internet, downlink up to 24 Mbps and uplink up to 1
Mbps.
The device supports WLAN access. It can connect to the Internet through a
WLAN AP or WLAN device. It complies with IEEE 802.11, 802.11b/g
specifications, WEP, WPA, and WPA2 security specifications.
1.1
Packing List
ADSL Wireless router
x1
Power adapter (DC) x1
ADSL splitter x 1
Quick Installation Guide x1
RJ45 Cable x1
RJ11 Cable x1
CD x1(user manual)
Warranty card X1
1.2 Safety Precautions
Follow the following instructions to prevent the device from risks and damage
caused by fire or electric power:
Use volume labels to mark the type of power.
Use the power adapter packed within the device package.
1
Pay attention to the power load of the outlet or prolonged lines. An
overburden power outlet or damaged lines and plugs may cause electric
shock or fire accident. Check the power cords regularly. If you find any
damage, replace it at once.
Proper space left for heat dissipation is necessary to avoid damage caused
by overheating to the device. The long and thin holes on the device are
designed for heat dissipation to ensure that the device works normally. Do
not cover these heat dissipation holes.
Do not put this device close to a place where a heat source exists or high
temperature occurs. Avoid the device from direct sunshine.
Do not put this device close to a place where it is over damp or watery. Do
not spill any fluid on this device.
Do not connect this device to any PCs or electronic products, unless our
customer engineer or your broadband provider instructs you to do this,
because any wrong connection may cause power or fire risk.
Do not place this device on an unstable surface or support.
1.3 LEDs and Interfaces
Front Panel
The following table describes the LEDs of the device:
LEDs
Power
Color
Green
Status
Description
The initialization of the device is
On
successful.
Off
The device is powered off.
Connection between the device and
ADSL
Green
On
the physical layer of the office is
established.
Slow
No signal is being detected.
Blinks
2
LEDs
Color
Status
Description
Fast
The device is handshaking with the
Blinks
physical layer of the office.
The Internet connection is normal in
the routing mode (for example: PPP
On
dial-up is successful), and no Internet
data is being transmitted.
Green
Internet data is being transmitted in
Blinks
Internet
the routing mode.
Off
The device is in the bridge mode.
The Internet connection fails after
Red
successful synchronization in the
On
routing mode (for example: PPP
dial-up is failed).
The LAN connection is nomal and
On
LAN4/3/2/1
Green
activated.
Data is being transmitted in the LAN
Blinks
or Internet data is being transmitted
in the bridge mode.
Off
The LAN interface is not connected.
The WLAN connection has been
On
WLAN
Green
activated.
Data is being transmitted in the
Blinks
WLAN.
The
Off
WPS
Green
WLAN
connection
is
not
activated.
WPS is enabled, and is waiting for
Blinks
client to negotiate.
Off
WPS is disabled.
Rear Panel
3
The following table describes the interfaces of the device:
Description
Interface
Press the button and hold it for 1 second, to enable WLAN.
Press the button and hold it for 1 second to 3 seconds, it does
WLAN/WPS not take effect.
Press the button and hold it for 3 or more than 3 seconds, to
initialize WPS negotiation.
DSL
LAN1/2/3/4
RJ-11 interface, for connecting to the ADSL interface or a
splitter through a telephone cable.
RJ-45 interface, for connecting to the Ethernet interface of a
computer or the Ethenet devices through an Ethernet cable.
Power
Power interface, for connecting to the power adapter
ON/OFF
Power switch, power on or power off the device.
Reset to the factory default configuration. Keep the device
Reset
powered on, and insert a needle into the hole for 3 to 6
seconds, then release it. The deivce is reset to the factory
default configuration.
1.4 System Requirements
Recommended system requirements are as follows:
A 10/100 base-T Ethernet card is installed on your PC
A hub or Switch. (connected to several PCs through one of Ethernet
interfaces on the device)
Operating system: Windows 98SE, Windows 2000, Windows ME,
Windows XP
Internet Explorer V5.0 or higher, Netscape V4.0 or higher, or Firefox 1.5 or
higher
4
1.5 Features
The device supports the following features:
Various line modes
External PPPoE dial-up access
Internal PPPoE/PPPoA dial-up access
1483Briged/1483Routed/MER/IPoA access
Multiple PVCs (up to eight) and these PVCs can be isolated from each
other
A single PVC with multiple sessions
Multiple PVCs with multiple sessions
802.1Q and 802.1P protocol
DHCP server
NAPT
Static route
Firmware upgrading through Web, TFTP, or FTP
Resetting to the factory defaults through Reset button or Web
DNS
Virtual server
DMZ
Two-level passwords and usernames
Web interface
Telnet CLI
System status display
PPP session PAP/CHAP
IP filter
IP quality of service (QoS)
Remote access control
Line connection status test
Remote managing through Telnet or HTTP
Backup and restoration of configuration file
Ethernet interface supporting crossover detection, auto-correction, and
polarity correction
Universal plug and play (UPnP)
5
2
Hardware Installation
Step 1
Connect the DSL interface of the device and the Modem interface of
the splitter through a telephone cable. Connect the phone to the
Phone interface of the splitter through a cable. Connect the incoming
line to the Line interface of the splitter.
The splitter has three interfaces:
Line: Connect to a wall phone jack (RJ-11 jack).
Modem: Connect to the ADSL jack of the device.
Phone: Connect to a telephone set.
Step 2
Connect the LAN interface of the device to the network card of the PC
through an Ethernet cable (MDI/MDIX).
I
Note:
Use twisted-pair cables to connect with the hub or switch.
Step 3
Plug one end of the power adapter to the wall outlet and connect the
other end to the Power interface of the device.
Connection 1
Figure 1 shows the application diagram for the connection of the router, PC,
splitter and the telephone sets, when no telephone set is placed before the
splitter.
6
Figure 1 Connection diagram (Without connecting telephone sets before the splitter)
Connection 2
Figure 2 shows the connection when the splitter is installed close to the router.
Figure 2 Connection diagram (Connecting a telephone set before the splitter)
Note:
When connection 2 is used, the filter must be installed close to the telephone
cable. See Figure2. Do not use the splitter to replace the filter.
Installing a telephone directly before the splitter may lead to failure of connection
between the device and the central office, or failure of Internet access, or slow
connection speed. If you really need to add a telephone set before the splitter,
7
you must add a microfilter before a telephone set. Do not connect several
telephones before the splitter or connect several telephones with the microfilter.
8
3
About the Web Configuration
This chapter describes how to configure the router by using the Web-based
configuration utility.
3.1 Access the Router
The following is the detailed description of accesing the router for the first time.
Step 1
Open the Internet Explorer (IE) browser and enter http://192.168.1.1.
Step 2
In the Login page that is displayed, enter the username and password.
The username and password of the super user are admin and admin.
The username and password of the common user are user and user.
If you log in as a super user, the page shown in the following figure appears. You
can check, configure and modify all the settings.
9
If you log in as a common user, you can check the status of the router, but can
not configure the most of the settings.
Note:
In the Web configuration page, you can click Apply Changes to save the
settings temporarily. If you want to save the settings of this page permanently,
click save of Attention that appears at the bottom of the Web page after the
configuration.
3.2 Wizard
When subscribing to a broadband service, you should be aware of the method by
which you are connected to the Internet. Your physical WAN device can be either
PPP, ADSL, or both. The technical information about the properties of your
Internet connection is provided by your Internet Service Provider (ISP). For
example, your ISP should inform you whether you are connected to the Internet
using a static or dynamic IP address, and the protocol that you use to
communicate on the Internet.
In the navigation bar, choose Wizard. The page shown in the following figure
appears. The Wizard page guides fast and accurate configuration of the Internet
connection and other important parameters. The following sections describe
these
various
configuration
parameters.
Whether
you
configure
these
parameters or use the default ones, click NEXT to enable your Internet
connection.
10
Enter the correct password and then click NEXT. The page shown in the
following figure appears. In this page, you can set the system time and Network
Time Protocol (NTP) server.
The following table describes the parameters of this page:
Description
Field
You can disable or enable NTP function. You have to
State
enable it if you want to configure the parameters in this
page.
Server IP
Interval
Enter the IP address of the specified time server manually.
Set the interval that the router obtains the time from the
time server. That is, the interval that the router verifies the
11
Description
Field
time with the server.
Time Zone
Choose the time zone of your country.
GMT time
It displays the Greenwich mean time.
After finishing the configuration, click NEXT. The page shown in the following
figure appears.
The following table describes the parameters of this page:
Description
Field
Country
Select the Country from the drop-down list.
Select the ISP according to the country from the
ISP
drop-down list. If you do not find the ISP that matches
the country, you can select Others.
Protocol
Select the WAN connection type. You can select from
the drop-down list.
12
Description
Field
Connection
You can select LLC or VC-Mux.
Type
VPI:Virtual path between two points in an ATM
network. Its valid value range is from 0 to 255.
VPI/VCI
VCI: The virtual channel between two points in an
ATM network, ranging from 32 to 65535 (0 to 31 is
reserved for local management of ATM traffic).
User name
The correct user name that your ISP provides to you.
Password
The correct password that your ISP provides to you.
After finishing the configuration, click NEXT. The page shown in the following
figure appears.
The following table describes the parameters of this page:
13
Description
Field
You can choose Enable or Disable. By default, WAN
WLAN
interface is enabled.
Interface
You need to enable WAN interface, and then you can
set the parameters in this page.
Choose the working mode of the router. You can choose
Band
802.11b, 802.11g, and Mixed(802.11b/11g). By default,
the band is Mixed (802.11b/11g).
The service set identification (SSID) is a unique name to
identify the router in the wireless LAN. Wireless stations
SSID
associating to the router must have the same SSID.
Enter a descriptive name that is used when the wireless
client connecting to the router.
Configure the wireless encryption mode. You can
choose None, WEP, WPA (TKIP), WPA (AES), WPA2
(AES), WPA2 (TKIP), or WPA2 Mixed.
Wired equivalent privacy (WEP) encrypts data
frames before transmitting over the wireless
network.
Encryption
Wi-Fi protected access (WPA) is a subset of the
IEEE802.11i security specification draft.
WPA2 Mixed is the collection of WPA and WPA2
encryption modes. The wireless client establishes
the connection between the router through WPA or
WPA2.
Key differences between WPA and WEP are user
authentication and improved data encryption.
After finishing the configuration, click NEXT. The page shown in the following
figure appears.
14
Note:
If the WAN connection type is set to PPPoA, the parameters of the WAN
connection type are the same as that of PPPoE. For the parameters in these
pages, refer to the parameter description of PPPoE.
1483 Bridged
In the WAN Interface Setup page, set the WAN connection type to 1483
Bridged. The page shown in the following figure appears.
15
Click NEXT. The page shown in the following figure appears.
The following table describes the parameters of this page:
Description
Field
You can choose Enable or Disable. By default, WAN
WLAN
interface is enabled.
Interface
You need to enable WAN interface, and then you can
set the parameters in this page.
16
Description
Field
Choose the working mode of the router. You can choose
Band
802.11b, 802.11g, and Mixed (802.11b/11g). By
default, the band is Mixed(802.11b/11g).
The service set identification (SSID) is a unique name to
identify the router in the wireless LAN. Wireless stations
SSID
associating to the router must have the same SSID.
Enter a descriptive name that is used when the wireless
client connecting to the router.
Configure the wireless encryption mode. You can
choose None, WEP, WPA (TKIP), WPA (AES), WPA2
(AES), WPA2 (TKIP), or WPA2 Mixed.
Wired equivalent privacy (WEP) encrypts data
frames before transmitting over the wireless
network.
Encryption
Wi-Fi protected access (WPA) is a subset of the
IEEE802.11i security specification draft.
WPA2 Mixed is the collection of WPA and WPA2
encryption modes. The wireless client establishes
the connection between the router through WPA or
WPA2.
Key differences between WPA and WEP are user
authentication and improved data encryption.
After finishing the configuration, click NEXT. The page shown in the following
figure appears.
17
1483 MER: DHCP
In the WAN Interface Setup page, set the WAN connection type to be 1483 MER:
DHCP. The page shown in the following figure appears.
The following table describes the parameters of this page:
Field
Country
ISP
Description
Select the Country from the drop-down list.
Select the ISP according to the country from the
drop-down list. If you do not find the ISP that matches
18
the country, you can select Others
Select the WAN connection type. You can select from
the drop-down list.
Protocol
Connection
You can select LLC or VC-Mux.
Type
VPI: Virtual path between two points in an ATM
network. Its valid value range is from 0 to 255.
VPI/VCI
VCI: The virtual channel between two points in an
ATM network, ranging from 32 to 65535 (0 to 31 is
reserved for local management of ATM traffic).
Click NEXT, the page shown in the following figure appears.
The following table describes the parameters of this page:
Description
Field
WLAN
You can choose Enable or Disable. By default, WAN
19
Description
Field
Interface
interface is enabled.
You need to enable WAN interface, and then you can
set the parameters in this page.
Choose the working mode of the router. You can choose
Band
802.11b, 802.11g, and Mixed (802.11b/11g). By
default, the band is Mixed (802.11b/11g)..
The service set identification (SSID) is a unique name to
identify the router in the wireless LAN. Wireless stations
SSID
associating to the router must have the same SSID.
Enter a descriptive name that is used when the wireless
client connecting to the router.
Configure the wireless encryption mode. You can
choose None, WEP, WPA (TKIP), WPA (AES), WPA2
(AES), WPA2 (TKIP), or WPA2 Mixed.
Wired equivalent privacy (WEP) encrypts data
frames before transmitting over the wireless
network.
Encryption
Wi-Fi protected access (WPA) is a subset of the
IEEE802.11i security specification draft.
WPA2 Mixed is the collection of WPA and WPA2
encryption modes. The wireless client establishes
the connection between the router through WPA or
WPA2.
Key differences between WPA and WEP are user
authentication and improved data encryption.
After finishing the configuration, click NEXT. The page shown in the following
figure appears.
20
1483 Routed/1483 MER: Static IP
The following table describes the parameters of this page:
Field
Country
Description
Select the Country from the drop-down list.
21
Select the ISP according to the country from the
ISP
drop-down list. If you do not find the ISP that matches
the country, you can select Others
Select the WAN connection type. You can select from
the drop-down list.
Protocol
Connection
You can select LLC or VC-Mux.
Type
VPI: Virtual path between two points in an ATM
network. Its valid value range is from 0 to 255.
VPI/VCI
VCI: The virtual channel between two points in an
ATM network, ranging from 32 to 65535 (0 to 31 is
reserved for local management of ATM traffic).
WAN
IP
Address
Subnet Mask
Enter the IP address of the WAN interface provided by
your ISP
Enter the subnet mask concerned to the IP address of
the WAN interface provided by your ISP
Click NEXT, the following page appears.
22
The following table describes the parameters of this page:
Description
Field
You can choose Enable or Disable. By default, WAN
WLAN
interface is enabled.
Interface
You need to enable WAN interface, and then you can
set the parameters in this page.
Choose the working mode of the router. You can choose
Band
802.11b, 802.11g, and Mixed (802.11b/11g). By
default, the band is Mixed(802.11b/11g)...
The service set identification (SSID) is a unique name to
identify the router in the wireless LAN. Wireless stations
SSID
associating to the router must have the same SSID.
Enter a descriptive name that is used when the wireless
client connecting to the router.
Configure the wireless encryption mode. You can
choose None, WEP, WPA (TKIP), WPA (AES), WPA2
(AES), WPA2 (TKIP), or WPA2 Mixed.
Wired equivalent privacy (WEP) encrypts data
frames before transmitting over the wireless
Encryption
network.
Wi-Fi protected access (WPA) is a subset of the
IEEE802.11i security specification draft.
WPA2 Mixed is the collection of WPA and WPA2
encryption modes. The wireless client establishes
the connection between the router through WPA or
23
Description
Field
WPA2.
Key differences between WPA and WEP are user
authentication and improved data encryption.
After finishing the configuration, click NEXT. The page shown in the following
figure appears.
Note:
If the WAN connection type is set to 1483 MER: Static IP, the parameters of
the WAN connection type are the same as that of 1483 Routed. For the
parameters in these pages, refer to the parameter description of 1483
Routed.
Click BACK to modify the settings.
Click FINISH to save the settings.
Click RESET to cancel the settings
3.3 Status
In the navigation bar, choose Status. In the Status page that is displayed
contains: System, LAN, WLAN, WAN, Port Mapping, Statistic, and ARP Table.
24
3.3.1
System
Choose Status > System. The page that is displayed shows the current status
and some basic settings of the router, such as software version, DSP version,
uptime, upstream speed, and downstream speed.
3.3.2
LAN
Choose Status > LAN. The page that is displayed shows some basic LAN
settings of the router. In this page, you can view the LAN IP address, DHCP
server status, MAC address, and DHCP client table. If you want to configure the
LAN network, refer to chapter 3.4.1.1 LAN IP.
3.3.3
WLAN
Choose Status > WLAN. The page that is displayed shows some basic settings
of wireless LAN (WLAN).
25
3.3.4
WAN
Choose Status > WAN. The page that is displayed shows some basic WAN
settings of the router. In this page, you can view basic status of WAN and DNS
server. If you want to configure the WAN network, refer to chapter 3.4.2.1 WAN.
3.3.5
Port Mapping
Choose Status > Port Mapping. In this page, you can view the mapping relation
and the status of port mapping.
26
3.3.6
Statistics
Choose Status > Statistics. The Statistics page that is displayed contains
Traffic Statistic and ADSL Statistic.
3.3.6.1
Traffic Statistic
Click Traffic Statistic in the left pane. The page shown in the following figure
appears. In this page, you can view the statistics of each network port.
27
3.3.6.2
ADSL Statistic
Click ADSL Statistic in the left pane. The page shown in the following figure
appears. In this page, you can view the ADSL line status, upstream rate,
downstream rate, and other information.
3.3.7
ARP Table
Choose Status > ARP Table. In the ARP Table page, you can view the table that
shows a list of learned MAC addresses.
3.4 Network
In the navigation bar, click Network. The Network page that is displayed
contains LAN, WAN, and WLAN.
28
3.4.1
LAN
Choose Network > LAN. The LAN page that is displayed contains LAN IP,
DHCP, and DHCP Static IP.
3.4.1.1
LAN IP
Click LAN IP in the left pane, the page shown in the following figure appears.
In this page, you can change IP address of the router. The default IP address is
192.168.1.1, which is the private IP address of the router.
The following table describes the parameters of this page:
Field
IP Address
Description
Enter the IP address of LAN interface. It is
recommended to use an address from a block that
29
Field
Description
is reserved for private use. This address block is
192.168.1.1- 192.168.255.254.
Enter the subnet mask of LAN interface. The range
Subnet Mask
of
subnet
mask
is
from
255.255.0.0-255.255.255.254.
Select it to enable the secondary LAN IP address.
Secondary IP
The two LAN IP addresses must be in the different
network.
You can choose the LAN interface you want to
LAN Port
configure.
You can select the following modes from the
Link Speed/Duplex
Mode
drop-downlist:100Mbps/FullDuplex,100Mbps/Half
Duplex,10Mbps/FullDuplex,10Mbps/Half
Duplex,Auto Negotiation.
It is the access control based on MAC address.
MAC
Address
Control
Select it, and the host whose MAC address is listed
in the Current Allowed MAC Address Table can
access the modem.
Enter MAC address, and then click it to add a new
Add
3.4.1.2
MAC address.
DHCP
Dynamic Host Configuration Protocol (DHCP) allows the individual PC to obain
the TCP/IP configuration from the centralized DHCP server. You can configure
this router as a DHCP server or disable it. The DHCP server can assign IP
address, IP default gateway, and DNS server to DHCP clients. This router can
also act as a surrogate DHCP server (DHCP Relay) where it relays IP address
assignment from an actual real DHCP server to clients. You can enable or
disable DHCP server.
Click DHCP in the left pane, the page shown in the following figure appears.
30
The following table describes the parameters of this page:
Field
Description
If set to DHCP Server, the router can assign IP
DHCP Mode
addresses, IP default gateway and DNS Servers to
the host in Windows95, Windows NT and other
operation systems that support the DHCP client.
It specifies the first and the last IP address in the IP
IP Pool Range
address pool. The router assigns IP address that is in
the IP pool range to the host.
Show Client
Default Gateway
Click it, the Active DHCP Client Table appears. It
shows IP addresses assigned to clients.
Enter the default gateway of the IP address pool.
The lease time determines the period that the host
Max Lease Time
retains the assigned IP addresses before the IP
addresses change.
Domain Name
Enter the domain name if you know. If you leave this
blank, the domain name obtained by DHCP from the
31
Field
Description
ISP is used. You must enter host name (system
name) on each individual PC. The domain name can
be assigned from the router through the DHCP
server.
DNS Servers
Set VendorClass
IP Range
You can configure the DNS server ip addresses for
DNS Relay.
Click it, the Device IP Range Table page appears.
You can configure the IP address range based on the
device type.
Click Show Client in the DHCP Mode page, the page shown in the following
figure appears. You can view the IP address assigned to each DHCP client.
The following table describes the parameters and buttons in this page:
Field
IP Address
Description
It displays the IP address assigned to the DHCP
client from the router.
It displays the MAC address of the DHCP client.
Each Ethernet device has a unique MAC address.
MAC Address
The MAC address is assigned at the factory and it
consists of six pairs of hexadecimal character, for
example, 00-A0-C5-00-02-12.
It displays the lease time. The lease time determines
Expired (s)
the period that the host retains the assigned IP
addresses before the IP addresses change.
Refresh
Click it to refresh this page.
Close
Click it to close this page.
32
Click Set VendorClass IP Range in the DHCP Mode page, the page as shown in
the following figure appears. In this page, you can configure the IP address range
based on the device type.
In the DHCP Mode field, choose None. The page shown in the following figure
appears.
In the DHCP Mode field, choose DHCP Relay. The page shown in the following
figure appears.
33
The following table describes the parameters and buttons of this page:
Field
Description
If set to DHCP Relay, the router acts a surrogate
DHCP Mode
DHCP Server and relays the DHCP requests and
Relay Server
Enter the DHCP server address provided by your ISP.
Apply Changes
Click it to save the settings of this page.
Reset
Click it to refresh this page.
reponses between the remote server and the client.
3.4.1.3
DHCP Static IP
Click DHCP Static IP in the left pane, the page shown in the following figure
appears. You can assign the IP addresses on the LAN to the specific individual
PCs based on their MAC address.
34
The following table describes the parameters and buttons of this page:
Field
Description
IP Address
Enter the specified IP address in the IP pool
MAC Address
Enter the MAC address of a host on the LAN.
Add
After entering the IP address and MAC address,
range, which is assigned to the host.
click it. A row will be added in the DHCP Static IP
Table.
Delete Selected
Select a row in the DHCP Static IP Table, then
click it, this row is deleted.
Reset
Click it to refresh this page.
DHCP Static IP Table
It shows the assigned IP address based on the
MAC address.
3.4.2
WAN
Choose Network > WAN. The WAN page that is displayed contains WAN, ATM
Setting, and ADSL Setting.
3.4.2.1
WAN
Click WAN in the left pane, the page shown in the following figure appears.
In this page, you can configure WAN interface of your router.
35
The following table describes the parameters of this page:
Field
Default Route Selection
VPI
Description
You can select Auto or Specified.
The virtual path between two points in an
ATM network, ranging from 0 to 255.
The virtual channel between two points in an
VCI
ATM network, ranging from 32 to 65535 (1 to
Encapsulation
You can choose LLC and VC-Mux.
31 are reserved for known protocols)
Channel Mode
You can choose 1483 Bridged, 1483 MER,
PPPoE, PPPoA, 1483 Routed or IPoA.
Select it to enable Network Address Port
Enable NAPT
Translation (NAPT) function. If you do not
select it and you want to access the Internet
normally, you must add a route on the uplink
36
Field
Description
equipment. Otherwise, the access to the
Internet fails. Normally, it is enabled.
Enabel IGMP
You can enable or disable Internet Group
Management Protocol (IGMP) function.
PPP Settings
User Name
Password
Type
Enter the correct user name for PPP dial-up,
which is provided by your ISP.
Enter the correct password for PPP dial-up,
which is provided by your ISP.
You can choose Continuous, Connect on
Demand, or Manual.
If set the type to Connect on Demand, you
need to enter the idle timeout time. Within the
Idle Time (min)
preset minutes, if the router does not detect
the flow of the user continuously, the router
automatically
disconnects
the
PPPoE
connection.
WAN IP Settings
You can choose Fixed IP or DHCP.
If select Fixed IP, you should enter the
local IP address, remote IP address
Type
and subnet mask.
If select DHCP, the router is a DHCP
client, the WAN IP address is assigned
by the remote DHCP server.
Local IP Address
Netmask
Unnumbered
Enter the IP address of WAN interface
provided by your ISP.
Enter the subnet mask of the local IP
address.
Select
this
checkbox
to
enable
IP
unnumbered function.
After configuring the parameters of this page,
Add
click it to add a new PVC into the Current
ATM VC Table.
37
Field
Description
Select a PVC in the Current ATM VC Table,
then modify the parameters of this PVC. After
Modify
finishing, click it to apply the settings of this
PVC.
This table shows the existed PVCs. It shows
the interface name, channel mode, VPI/VCI,
Current ATM VC Table
encapsulation
mode,
local
IP
address,
remote IP address and other information. The
maximum item of this table is eight.
Click
in the PPPoE mode, the page shown in the following figure appears. In
this page, you can configure parameters of this PPPoE PVC.
The following table describes the parameters and buttons of this page:
Field
Protocol
Description
It displays the protocol type used for this WAN
connection.
ATM VCC
The ATM virtual circuit connection assigned for
this PPP interface (VPI/VCI).
38
Field
Description
Login Name
The user name provided by your ISP.
Password
The password provided by your ISP.
Authentication Method
You can choose AUTO, CHAP, or PAP.
Connection Type
You can choose Continuous, Connect on
Demand, or Manual.
Idle Time (s)
If choose Connect on Demand, you need to
enter the idle timeout time. Within the preset
minutes, if the router does not detect the flow of
the user continuously, the router automatically
disconnects the PPPoE connection.
Bridge
You can select Bridged Ethernet, Bridged
PPPoE, or Disable Bridge.
AC-Name
The accessed equipment type.
Service-Name
The service name.
802.1q
You can select Disable or Enable. After enable
it, you need to enter the VLAN ID. The value
ranges from 1 to 4095.
Apply Changes
Click it to save the settings of this page
temporarily.
Return
Click it to return to the Channel Configuration
page.
Reset
Click it to refresh this page.
Source Mac address
The MAC address you want to clone.
MAC Clone
Click it to enable the MAC Clone function with
the MAC address that is configured.
3.4.2.2
ATM Setting
Click ATM Setting in the left pane, the page shown in the following figure
appears. In this page, you can configure the parameters of the ATM, including
QoS, PCR, CDVT, SCR, and MBS.
39
The following table describes the parameters of this page:
Field
Description
VPI
The virtual path identifier of the ATM PVC.
VCI
The virtual channel identifier of the ATM PVC.
QoS
The QoS category of the PVC. You can choose
UBR, CBR, rt-VBR, or nrt-VBR.
PCR
Peak cell rate (PCR) is the maximum rate at
which cells can be transmitted along a connection
in the ATM network. Its value ranges from 1 to
65535.
CDVT
Cell delay variation tolerance (CDVT) is the
amount of delay permitted between ATM cells (in
microseconds). Its value ranges from 0 to
4294967295.
SCR
Subtain cell rate (SCR) is the maximum rate that
traffic can pass over a PVC without the risk of cell
loss. Its value ranges from 0 to 65535.
MBS
Maximum burst size (MBS) is the maximum
number of cells that can be transmitted at the
PCR. Its value ranges from 0 to 65535.
40
3.4.2.3
ADSL Setting
Click ADSL Setting in the left pane, the page shown in the following figure
appears. In this page, you can select the DSL modulation. Mostly, you need to
remain this factory default settings. The router supports these modulations:
G.Lite, G.Dmt, T1.413, ADSL2, ADSL2+, AnnexL, and AnnexM. The router
negotiates the modulation modes with the DSLAM.
3.4.3
3.4.3.1
WLAN
Basic Settings
Choose WLAN > Basic Settings and the following page appears. In this page,
you can configure the parameters for wireless LAN clients that may connect to
the modem.
41
The following table describes the parameters of this page:
Field
Description
Choose the working mode of the modem. You can
choose from drop-down list.
Band
By default, the band is 2.4 GHz (B + G).
Choose the network model of the modem, which
Mode
is varied according to the software. By default, the
network model of the modem is AP.
The service set identification (SSID) is a unique
name to identify the modem in the wireless LAN.
SSID
Wireless stations associating to the modem must
have the same SSID. Enter a descriptive name
that is used when the wireless client connecting to
the modem.
A channel is the radio frequency used by
802.11b/g/n wireless devices. There are 13
Channel Number
channels (from 1 to 13) available depending on
the geographical area. You may have a choice of
channels (for your region) and you should use a
different channel from an adjacent AP to reduce
42
Field
Description
the interference. Interference and degrading
performance occurs when radio signal from
different APs overlap.
Choose a channel from the drop-down list box.
You can choose the transmission power of the
Radio Power
radio signal. The default one is 100%. It is
recommended to choose the default value100%.
Show Active Clients
Click it to view the information of the wireless
clients that are connected to the modem.
Click it to apply the settings temporarily. If you
Apply Changes
want to save the settings of this page
permanently, click Save in the lower left corner.
3.4.3.2
Security
Choose Wireless > Security and the following page appears.
The following table describes the parameters of this page:
Field
Description
Configure the wireless encryption mode. You can
Encryption
choose None, WEP, WPA (TKIP), WPA (AES),
WPA2 (AES), WPA2 (TKIP), or WPA2 Mixed.
Wired equivalent privacy (WEP) encrypts
43
Field
Description
data frames before transmitting over the
wireless network.
Wi-Fi protected access (WPA) is a subset of
the
IEEE802.11i
security
specification
draft.
WPA2 Mixed is the collection of WPA and
WPA2 encryption modes. The wireless
client establishes the connection between
the modem through WPA or WPA2.
Key differences between WPA and WEP are user
authentication and improved data encryption.
It is available when you set the encryption mode
Set WEP Key
to WEP. Click it, the Wireless WEP Key Setup
page appears.
Select Personal (Pre-Shared Key), enter the
pre-shared key in the Pre-Shared Key
field.
Select Enterprise (RADIUS), enter the port,
IP address, and password of the Radius
WPA Authentication
server. You need to enter the username
Mode
and password provided by the Radius
server when the wireless client connects
the modem.
If the encrypton is set to WEP, the modem uses
802.1 X authentication, which is Radius
authentication.
Click Set WEP Key, and the following page appears.
44
The following describes the parameters of this page:
Field
Key Length
Description
Choose the WEP key length. You can Choose
64-bit or 128-bit.
If you choose 64-bit, you can choose ASCII (5
Key Format
characters) or Hex (10 characters).
If you choose 128-bit, you can choose ASCII
(13 characters) or Hex (26 characters).
Default Tx Key
Choose the index of WEP Key. You can choose Key
1, Key 2, Key 3, or Key 4.
The Encryption keys are used to encrypt the data.
Both the modem and wireless stations must use the
same encryption key for data transmission.
If you choose 64-bit and ASCII (5 characters),
Encryption Key 1
to 4
enter any 5 ASCII characters.
If you choose 64-bit and Hex (10 characters),
enter any 10 hexadecimal characters.
If
you
choose
128-bit
and
ASCII
(13
characters), enter any 13 ASCII characters.
If you choose 128-bit and Hex (26 characters),
enter any 26 hexadecimal characters.
45
Field
Description
Click it to apply the settings temporarily. If you want
Apply Changes
to save the settings of this page permanently, click
Save in the lower left corner.
3.4.3.3
Access Control
Choose WLAN > Access Control and the following page appears. In this page,
you can configure the access control of the wireless clients.
Choose Allow Listed as the access control mode to enable white list function.
Only the devices whose MAC addresses are listed in the Current Access
Control List can access the modem.
Choose Deny Listed as the access control mode to to enable black list function.
The devices whose MAC addresses are listed in the Current Access Control
List are denied to access the modem.
3.4.3.4
Advanced Settings
Choose Wireless > Advanced Settings and the following page appears. In this
page, you can configure the wireless advanced parameters. It is recommended
to use the default parameters.
Note:
46
The parameters in the Advanced Settings are modified by the professional
personnel, it is recommended to keep the default values.
The following table describes the parameters of this page:
Field
Description
Select the modem operating in the open system or
encryption authentication. You can choose Open
System, Shared Key, or Auto.
Authentication
In the open system, the wireless client can
directly connect to the device
In the encryption authentication, the wireless
client connects to the modem through the
shared key.
Choose the transmission rate of the wireless data.
Data Rate
You can choose Auto, 1 M, 2 M, 5.5 M, 11 M, 6 M,
9 M, 12 M, 18 M, 24 M, 36 M, 48 M, 54M.
Long Preamble: It means this card always
PreambleType
use long preamble.
Short Preamble: It means this card can
support short preamble capability.
Broadcast SSID
Select whether the modem broadcasts SSID or not.
47
Field
Description
You can select Enable or Disable.
Select Enable, the wireless client searches the
modem through broadcasting SSID.
Select Disable to hide SSID, the wireless
clients can not find the SSID.
Wireless isolation. Select Enable, the wireless
Relay Blocking
clients that are connected to the modem can not
intercommunication.
Ethernet to
Whether the wireless network can communicate
Wireless Blocking
with the Ethernet network or not.
Wifi Multicast to
Enable it to using unicast to transmit multicast
Unicast
packet
3.4.3.5
WPS
Choose WLAN > WPS and the following page appears.
There are two ways for the wireless client to establish the connection with the
modem through WPS. The modem generates PIN, see the above figure. Click
Regenerate PIN to generate a new PIN, and then click Start PBC, In the
wireless client tool, enter the PIN which is generated by the modem,start
connection. The client will automatically establish the connection with the modem
through the encryption mode, and you need not to enter the key. The other way is
the wireless client generates PIN. In the above figure, enter PIN of the wireless
48
client in the Client PIN Number field, then click Start PIN to establish the
connection.
Note:
The wireless client establishes the connection with the modem through WPS
negotiation.The wireless client must support WPS
3.5
Service
In the navigation bar, click Service. In the Service page that is displayed
contains DNS, Firewall, UPNP, IGMP Proxy, TR-069, and ACL.
3.5.1 DNS
Domain Name System (DNS) is an Internet service that translates the domain
name into IP address. Because the domain name is alphabetic, it is easier to
remember. The Internet, however, is based on IP addresses. Every time you use
a domain name, DNS translates the name into the corresponding IP address. For
example, the domain name www.example.com might be translated to
198.105.232.4. The DNS has its own network. If one DNS server does not know
how to translate a particular domain name, it asks another one, and so on, until
the correct IP address is returned.
Choose Service > DNS. The DNS page that is displayed contains DNS and
DDNS.
3.5.1.1
DNS
Click DNS in the left pane, the page shown in the following figure appears.
49
The following table describes the parameters and buttons of this page:
Field
Obtain DNS
Automatically
Description
Select it, the router accepts the first received DNS
assignment from one of the PPPoA, PPPoE or MER
enabled PVC(s) during the connection establishment.
Set DNS
Select it, enter the IP addresses of the primary and
Manually
secondary DNS server.
Apply Changes
Click it to save the settings of this page.
Reset
Click it to start configuring the paremters in this page.
3.5.1.2
DDNS
Click DDNS in the left pane, the page shown in the following figure appears. This
page is used to configure the dynamic DNS address from DynDNS.org or TZO.
You can add or remove to configure dynamic DNS.
The following table describes the parameters of this page:
Field
Description
50
Field
DDNS provider
Description
Choose the DDNS provider name. You can choose
DynDNS.org or TZO.
Host Name
The DDNS identifier.
Interface
The WAN interface of the router.
Enable
Enable or disable DDNS function.
Username
The name provided by DDNS provider.
Password
The password provided by DDNS provider.
Email
The email provided by DDNS provider.
Key
The key provided by DDNS provider.
3.5.2 Firewall
Choose Service > Firewall. The Firewall page that is displayed contains IP/Port
Fileter, MAC Filter, URL Blocking, Virtual Server, IP Address Mapping, DMZ
Setting, NAT EXCLUDE IP, ALG Setting, and Anti-DoS.
3.5.2.1 IP/Port Filter
Click IP/Port Filter in the left pane, the page shown in the following figure
appears. Entries in the table are used to restrict certain types of data packets
through the gateway. These filters are helpful in securing or restricting your local
network.
51
3.5.2.2 MAC Filter
Click MAC Filter in the left pane, the page shown in the following figure appears.
Entries in the table are used to restrict certain types of data packets from your
local network to Internet through the gateway. These filters are helpful in securing
or restricting your local network.
52
3.5.2.3 URL Blocking
Click URL Blocking in the left pane, the page shown in the following figure
appears. This page is used to block a fully qualified domain name, such as
tw.yahoo.comand and filtered keyword. You can add or delete FQDN and filtered
keyword.
The following table describes the parameters and buttons of this page:
Field
URL Blocking
Capability
Description
You can choose Disable or Enable.
Select Disable to disable URL blocking function
and keyword filtering function.
Select Enable to block access to the URLs and
keywords specified in the URL Blocking Table.
Keyword
Enter the keyword to block.
AddKeyword
Click it to add a keyword to the URL Blocking Table.
Delete Selected
Select a row in the URL Blocking Table and click it to
Keyword
delete the row.
URL Blocking
A list of the URL (s) to which access is blocked.
Table
3.5.2.4
Virtual Server
Click Virtual Server in the left pane, the page shown in the following figure
appears.
53
The following table describes the parameters of this page:
Field
Description
You can select the common service type, for
example, AUTH, DNS, or FTP. You can also define
a service name.
Service Type
If you select Usual Service Name, the
corresponding parameter has the default
settings.
If you select User-defined Service Name, you
need to enter the corresponding parameters.
Protocol
WAN Setting
WAN Interface
WAN Port
LAN Open Port
Choose the transport layer protocol that the service
type uses. You can choose TCP or UDP.
You can choose Interface or IP Address.
Choose the WAN interface that will apply virtual
server.
Choose the access port on the WAN.
Enter the port number of the specified service type.
Enter the IP address of the virtual server. It is in the
LAN IP Address
same network segment with LAN IP address of the
router.
54
3.5.2.5 IP Address Mapping
NAT is short for Network Address Translation. The Network Address Translation
Settings window allows you to share one WAN IP address for multiple computers
on your LAN.
Click IP Address Mapping in the left pane, the page shown in the following
figure appears.
Entries in this table allow you to configure one IP pool for specified source IP
address from LAN, so one packet whose source IP is in range of the specified
address will select one IP address from the pool for NAT.
3.5.2.6 DMZ Setting
Demilitarized Zone (DMZ) is used to provide Internet services without sacrificing
unauthorized access to its local private network. Typically, the DMZ host contains
devices accessible to Internet traffic, such as web (HTTP) servers, FTP servers,
SMTP (e-mail) servers and DNS servers.
Click DMZ Setting in the left pane, the page shown in the following figure
appears.
The following describes how to configure DMZ.
Step 1
Select Enable DMZ to enable this function.
Step 2
Enter an IP address of the DMZ host.
Step 3
Click Apply Changes to save the settings of this page temporarily.
55
3.5.2.7 NAT EXCLUDE IP
Click NAT EXCLUDE IP in the left pane, the page shown in the following figure
appears.
In the page, you can configure some source IP addresses which use the purge
route mode when accessing internet through the specified interface.
3.5.2.8 ALG Setting
Click ALG Setting in the left pane, the page shown in the following figure
appears.
56
3.5.2.9
Anti-DoS
Denial-of-Service Attack (DoS attack) is a type of attack on a network that is
designed to bring the network to its knees by flooding it with useless traffic.
Click Anti-DoS in the left pane, the page shown in the following figure appears. In
this page, you can prevent DoS attacks.
57
3.5.3
UPNP
Choose Service > UPnP, the page shown in the following figure appears. This
page is used to configure UPnP. The system acts as a daemon after you enable
it.
58
3.5.4
IGMP Proxy
Choose Service > IGMP Proxy, the page shown in the following figure appears.
IGMP proxy enables the system to issue IGMP host messages on behalf of hosts
that the system discovered through standard IGMP interfaces. The system acts
as a proxy for its hosts after you enable it.
3.5.5
TR-069
Choose Service > TR-069, the page shown in the following page appears. In this
page, you can configure the TR-069 CPE.
59
The following table describes the parameters of this page:
Field
Description
ACS
URL
The URL of the auto-configuration server to
connect to.
User Name
The user name for logging in to the ACS.
Password
The password for logging in to the ACS.
Periodic Inform Enable
Select Enable to periodically connect to the
ACS to check whether the configuration
updates.
60
Field
Description
Periodic Inform
Specify the amount of time between
Interval
connections to ACS.
Connection Request
User Name
The connection usrname provided by TR-069
service.
Password
The connection password provided by TR-069
service.
Debug
Show Message
Select Enable to display ACS SOAP messages
on the serial console.
CPE sends GetRPC
Select Enbale, the router contacts the ACS to
obtain configuration updates.
Skip MReboot
Specify whether to send an MReboot event
Delay
Specify whether to start the TR-069 program
code in the inform message.
after a short delay.
Auto-Execution
Specify whether to automatically start the
TR-069 after the router is powered on.
3.5.6
ACL
Choose Service > ACL, the page shown in the following figure appears. In this
page, you can permit the data packets from LAN or WAN to access the router.
You can configure the IP address for Access Control List (ACL). If ACL is enabled,
only the effective IP address in the ACL can access the router.
Note:
If you select Enable in ACL capability, ensure that your host IP address is in
ACL list before it takes effect.
61
The following table describes the parameters and buttons of this page:
Field
Direction Select
LAN ACL Switch
Description
Select the router interface. You can select LAN or
WAN. In this example, LAN is selected.
Select it to enable or disable ACL function.
Enter the IP address of the specified interface. Only
IP Address
the IP address that is in the same network segment
with the IP address of the specified interface can
access the router.
You can choose the following services from LAN:
Services Allowed
Web, Telnet, FTP, TFTP, SNMP, or PING. You can
also choose all the services.
Add
Reset
After setting the parameters, click it to add an entry
to the Current ACL Table.
Click it to refresh this page.
Set direction of the data packets to WAN, the page shown in the following figure
appears.
62
The following table describes the parameters and buttons of this page:
Field
Direction Select
WAN Setting
WAN Interface
Description
Select the router interface. You can select LAN or
WAN. In this example, WAN is selected.
You can choose Interface or IP Address.
Choose the interface that permits data packets from
WAN to access the router.
Enter the IP address on the WAN. Only the IP
IP Address
address that is in the same network segment with
the IP address on the WAN can access the router.
You can choose the following services from WAN:
Services Allowed
Web, Telnet, FTP, TFTP, SNMP, or PING. You can
also choose all the services.
Add
Reset
After setting the parameters, click it to add an entry
to the Current ACL Table.
Click it to refresh this page.
63
3.6
Advance
In the navigation bar, click Advance. In the Advance page that is displayed
contains Bridge Setting, Routing, Port Mapping, QoS, SNMP and Others.
3.6.1
Bridge Setting
Choose Advance > Bridge Setting, the page shown in the following figure
appears. This page is used to configure the bridge parameters. You can change
the settings or view some information on the bridge and its attached ports.
The following table describes the parameters and button of this page:
Field
Aging Time
Description
If the host is idle for 300 seconds (default value), its
entry is deleted from the bridge table.
802.1d Spanning
You can select Disabled or Enabled.
Tree
Select Enabled to provide path redundancy while
preventing undesirable loops in your network.
Show MACs
Click it to show a list of the learned MAC addresses
for the bridge.
Click Show MACs, the page shown in the following figure appears. This table
shows a list of learned MAC addresses for this bridge.
64
3.6.2 Routing
Choose Advance > Routing, the page shown in the following figure appears.
The page that is displayed contains Static Route and RIP.
3.6.2.1 Static Route
Click Static Route in the left pane, the page shown in the following figure
appears. This page is used to configure the routing information. You can add or
delete IP routes.
The following table describes the parameters and buttons of this page:
Field
Enable
Description
Select it to use static IP routes.
65
Field
Description
Destination
Enter the IP address of the destination device.
Subnet Mask
Enter the subnet mask of the destination device.
Next Hop
Enter the IP address of the next hop in the IP route to the
destination device.
Metric
The metric cost for the destination.
Interface
The interface for the specified route.
Add Route
Click it to add the new static route to the Static Route
Table.
Update
Select a row in the Static Route Table and modify the
parameters. Then click it to save the settings temporarily.
Delete
Select a row in the Static Route Table and click it to
Selected
delete the row.
Show
Click it, the IP Route Table appears. You can view a list
Routes
of destination routes commonly accessed by your
network.
Static Route
A list of the previously configured static IP routes.
Table
Click Show Routes, the page shown in the following figure appears. The table
shows a list of destination routes commonly accessed by your network.
3.6.2.2 RIP
Click RIP in the left pane, the page shown in the following figure appears. If you
are using this device as a RIP-enabled router to communicate with others using
Routing Information Protocol (RIP), enable RIP. This page is used to select the
interfaces on your devices that use RIP, and the version of the protocol used.
66
The following table describes the parameters and buttons of this page:
Field
RIP
Description
Select Enable, the router communicates with other
RIP-enabled devices.
Apply Changes
Click it to save the settings of this page.
Interface
Choose the router interface that uses RIP.
Receive Version
Choose the interface version that receives RIP
messages. You can choose RIP1, RIP2, or Both.
Choose RIP1 indicates the router receives RIP
v1 messages.
Choose RIP2 indicates the router receives RIP
v2 messages.
Choose Both indicates the router receives RIP
v1 and RIP v2 messages.
Send Version
The working mode for sending RIP messages. You
can choose RIP1 or RIP2.
Choose RIP1 indicates the router broadcasts
RIP1 messages only.
Choose RIP2 indicates the router multicasts
RIP2 messages only.
Add
Click it to add the RIP interface to the Rip
Configration List.
Delete
Select a row in the Rip Configration List and click
it to delete the row.
67
3.6.3
Port Mapping
Choose Advance > Port Mapping. The page shown in the following figure
appears. In this page, you can bind the WAN interface and the LAN interface to
the same group.
The procedure for manipulating a mapping group is as follows:
Step 1
Select Enable to enable this function.
Step 2
Select a group from the table.
Step 3
Select interfaces from the WAN and LAN interface list and add them to
the grouped interface list using the arrow buttons to manipulate the
required mapping of the ports.
Click Apply Changes to save the changes.
68
3.6.4
QoS
Choose Advance > QoS, the page shown in the following figure appears. Entries
in the QoS Rule List are used to assign the precedence for each incoming
packet based on physical LAN port, TCP/UDP port number, source IP address,
destination IP address and other information.
Step 4
Enable IP QoS and click Apply to enable IP QoS function.
Step 5
Click add rule to add a new IP QoS rule.
The page shown in the following figure appears.
69
The following table describes the parameters and buttons of this page:
Field
IP QoS
Description
Select to enable or disable IP QoS function. You need
to enable IP QoS if you want to configure the
parameters of this page.
QoS Policy
You can choose stream based, 802.1p based, or
Schedule Mode
You can choose strict prior or WFQ (4:3:2:1).
DSCP based.
Source IP
The IP address of the source data packet.
Source Mask
The subnet mask of the source IP address.
Destination IP
The IP address of the destination data packet.
Destination
The subnet mask of the destination IP address.
70
Field
Description
Mask
Source Port
The port of the source data packet.
Destination Port
The port of the destination data packet.
Protocol
The protocol responds to the IP QoS rules. You can
choose TCP, UDP, or ICMP.
Physical Port
Set priority
The LAN interface responds to the IP QoS rules.
The priority of the IP QoS rules. P0 is the highest
priority and P3 is the lowest.
IP Precedence
You can choose from 0 to 7 define the priority in the
IP ToS
The type of IP ToS for classifying the data package
ToS of the IP data packet.
You can choose Normal Service, Minimize Cost,
Maximize Reliability, Maximize Throughput, or
Minimize Delay.
802.1p
You can choose from 0 to 7.
delete
Select a row in the QoS rule list and click it to delete
delete all
Select all the rows in the QoS rule list and click it to
the row.
delete the rows.
3.6.5
SNMP
Choose Advance > SNMP, the page shown in the following figure appears. You
can configure the SNMP parameters.
71
The following table describes the parameters of this page:
Description
Field
Select it to enable SNMP function. You need to
Enable SNMP
enable SNMP, then you can configure the
parameters of this page.
Trap IP Address
Enter the trap IP address. The trap information is
sent to the corresponding host.
Community Name
The network administrators must use this password
(Read-only)
to read the information of this router.
Community Name
The network administrators must use this password
(Read-Write)
3.6.6
to configure the information of the router.
Others
Choose Advance > Others, the page shown in the following figure appears.
72
3.7 Admin
In the navigation bar, click Admin. The Admin page that is displayed contains
Commit/Reboot, Upgrade, System Log, Password, Time Zone and. Logout.
3.7.1
Commit/Reboot
Choose Admin > Commit/Reboot, the page shown in the following figure
appears. You can set the router reset to the default settings or set the router to
commit the current settings.
The following table describes the parameters and button of this page:
Field
Description
You can choose Save the current
configuration or Restore to the factory
default configuration.
Reboot from
Save the current configuration: Save
the current settings, and then reboot the
router.
Restore to the factory default
73
Field
Description
configuration: Reset to the factory
default settings, and then reboot the the
router.
Reboot
3.7.2
Click it to reboot the router.
Upgrade
Choose Admin > Upgrade. The Upgrade page that is displayed contains
Upgrade Firmware and Backup/Restore.
Caution:
Do not turn off the router or press the Reset button while the procedure
is in progress.
3.7.2.1
Upgrade Firmware
Click Upgrade Firmware in the left pane, the page shown in the following figure
appears. In this page, you can upgrade the firmware of the router.
The following table describes the parameters and button of this page:
Field
Select File
Upload
Description
Click Browse to select the firmware file.
After selecting the firmware file, click Upload to
starting upgrading the firmware file.
74
Reset
3.7.2.2
Click it to starting selecting the firmware file.
Backup/Restore
Click Backup/Restore in the left pane, the page shown in the following figure
appears. You can backup the current settings to a file and restore the settings
from the file that was saved previously.
The following table describes the parameters and button of this page:
Field
Save Settings to File
Load Settings from File
Description
Click it, and select the path. Then you can save
the configuration file of the router.
Click Browse to select the configuration file.
After selecting the configuration file of the
Upload
router, click Upload to start uploading the
configuration file of the router.
3.7.3
System Log
Choose Admin > System Log, the page shown in the following figure appears.
In this page, you can enable or disable system log function and view the system
log.
75
3.7.4
Password
Choose Admin > Password, the page shown in the following figure appears. By
default, the user name and password are admin and admin respectively. The
common user name and password are user and user respectively.
The following table describes the parameters of this page:
Field
User Name
Privilege
Description
Choose the user name for accessing the
router. You can choose admin or user.
Choose the privilege for the account.
76
Field
Old Password
New Password
Confirm Password
3.7.5
Description
Enter the old password
Enter the password to which you want to
change the old password.
Enter the new password again.
Time Zone
Choose Admin > Time Zone, the page shown in the following figure appears.
You can configure the system time manually or get the system time from the time
server.
The following table describes the parameters of this page:
Field
System Time
Description
Set the system time manually.
NTP Configuration
State
Select enable or disable NTP function. You need
77
Field
Description
to enable NTP if you want to configure the
parameters of NTP.
Primary Server
Set the primary NTP server manually.
Secondary Server
Set the secondary NTP server manually.
Time Zone
3.7.6
Choose the time zone in which area you are from
the drop down list.
Logout
Choose Admin > Logout, the page shown in the following figure appears.
3.8 Diagnostic
In the navigation bar, click Diagnostic. The Diagnostic page that is displayed
contains Ping, ATM Loopback, ADSL and Diagnostic Test.
3.8.1
Ping
Choose Diagnostic > Ping. The page shown in the following figure appears.
The following table describes the parameter and button of this page:
Field
Host
Description
Enter the valid IP address or domain name.
78
Run Ping
3.8.2
Click it to start to Ping.
ATM Loopback
Choose Diagnostic > ATM Loopback. The page shown in the following figure
appears. In this page, you can use VCC loopback function to check the
connectivity of the VCC. The ATM loopback test is useful for troubleshooting
problems with the DSLAM and ATM network.
Click Run Loopback to start testing.
3.8.3
ADSL
Choose Diagnostic > ADSL. The page shown in the following figure appears. It
is used for ADSL tone diagnostics.
79
Click Start to start ADSL tone diagnostics.
3.8.4
Diagnostic Test
Choose Diagnostic > Diagnostic Test, the page shown in the following figure
appears. In this page, you can test the DSL connection. You can also view the
LAN status connection and ADSL connection.
Click Run Diagnostic Test to start testing.
80